The water heater is a very essential appliance of your household but do you know that it accounts for 15% of the energy bill expenses?
It’s practical that you cannot do without a heater but you can definitely use it rationally to conserve energy and save from your pocket.
Here are a few quick tips to save on your water heating energy bill:
Turning down the temperature
Go to the warm setting and just turn down the temperature and this will prevent your skin from getting burnt anytime apart from saving energy.
You would need the heater daily throughout the cold season so you can imagine how much energy would be consumed in these months. The usual setting is 140 degrees F but you can lower it to 120 degrees F to save a 6% to 10% from the energy bill. Just refer to the manual while adjusting the thermostat.
Use the water heater less
Could you use the water heater less? Showers are mainly responsible for your soaring water heating costs. You can use showerheads with low-flow, complete your shower quickly, turn off the water supply while you are using soap and always use lukewarm water.
You can endure a bit and try using cold water in washing clothes because a lot of water goes in washing clothes.
Water heater inspection
Do you get your heater inspected every year before the winters? It is actually a good idea to do so and prevent from applying huge energy bills. Just before the onset of the spring and in the summer months get an inspection to ensure the heater is working optimally.
Gallons of water is wasted every year due to boiler leaks so don’t wait to mend boiler leaks but get early and quick solution.
Call a professional plumber in Chicago to detect leaks and get repaired. While water is being wasted, your bills are rising!
You can switch to solar or tankless systems
If you have decided to replace your old water heating system, you can invest a little more and purchase the solar or tankless systems. If you do so, your energy costs would be slashed down by half of what you pay. Isn’t it a great option for the households? You can give it a thought.
It is practically inexpensive to add insulation but doing so can cut down standby loss of heat by 25% to 50% and this would directly cut down heating costs by 5% to 10%.
Reuse the water
So much of hot water flows down the drain but did you hear about ‘drain water heat recovery systems’? It’s basically a technology to arrest the energy that flows down the drain to pre-heat the cold water that is making its way into the heater.
These systems are priced within $300-$500 and you can call your plumber in Chicago area to install. You invest once and reap the benefits of it through low water heating bills.
Buy an efficient model
If your water heating system is old, invest in a new one because old systems tend to consume more electricity. Buy energy star models where you can save 15% of the total cost of energy bills.
You can also invest in a system with heat traps fore more energy efficiency.
Simply set a timer
A lot of energy is invested in retaining the heat inside the water all 24 hours. Since you don’t need to use water all 24 hours, then why not set a timer to turn off during the sleep time hours or before you leave home for work?
This can help to conserve about 5% to 12% energy. Buy a timer for about $60 and enjoy the hassle free benefits.
Now that you know so many tips to save water heating costs, try these out. If you encounter any problems, call us immediately! We’re licensed and we can refer you to certified local plumbers in Chicago, IL.
A water heater’s energy efficiency is measured by the correspondence between the electrical input and hot water productivity, installing your water heater on your own will affect its efficiency and will additionally cause you more on your expenses.
It is critical to have your water heating system installed by our water heater specialists to maximize its energy efficiency. A lot of people also try to take on DIY projects in order to save them the cost and probably pick up a new skill in the process.
Most often, they do this without understanding that they may possibly do things incorrectly and damage the whole system in the end. Your water heater is a delicate equipment that needs to be handled meticulously, otherwise you’ll end up with an ineffective water heating system.
This is the reason why you need to get the help of our licensed local plumbing specialists to install your heating device accordingly. Proper installation also guarantees that your water heater will run at maximum efficiency and give you sufficient amount of needed water.
In This Article, We Will Be Covering:
The signs of hot water tank problems
What to watch out for when it comes to your water heater
Water heater troubleshooting
When you should replace your water heater
Why your water heater isn’t working
How to choose an electric water heating system
Tank-type vs tankless water heaters
Common hot water problems in every household
Where you can get reliable hot water heater service
Who can fix your water heater
Who to call for repairs
What are the Signs of Hot Water Tank Problems?
Most people take their hot water heater for granted. It’s out of sight, out of mind, so as long as it’s working, we don’t really think about it.
And generally, it’s working. This appliance is most often dependable and rarely experiences trouble. But there are times when you may have a problem that means you need a hot water heater repair, so worry no more because we are here to help!
Some things to watch out for when it comes to your hot water heater
Popping noise, like sound of boiling water
Offensive smell, often like rotten eggs
Water Heater Troubleshooting: What Do I Check for in My Heating Unit?
Faucets and appliances are no longer producing hot water
Water is no longer sufficiently hot, even though you have not changed the temperature setting
If you experience these issues, the most likely cause is a faulty part or faulty installation. Call us for any repair, or maintenance services you may need.
We can also recommend hot water heater upgrades and offer top-quality products and expert installation.
Gas water heaters
Electric water heaters
Tankless water heaters
Parts and supplies
Signs You Need to Replace Your Water Heater
Are you unsure whether your water heater is in need of repair or has burned out altogether? If you notice a problem in your water heater, here are a few ways in which you can troubleshoot for a solution.
These tips will also help you to identify and understand signs that it’s time to replace your water heater.
Water heaters are available in two types, electric and gas water heaters. It is possible to use electric water heaters almost anywhere. However, gas water heaters are mostly installed in houses that already receive a gas supply.
Water heater, unlike the other household appliances, undergoes the maximum workout. Most water heaters available on the market have a lifespan of not more than 8 to 12 years.
This however, varies according to factors such as the severity of the prevailing temperature, quality of the installation, the unit design, and the overall water heater maintenanceyour unit has received.
If your water heater is already ten years old and has started leaking from the base of the tank or functions erratically, it is probably the time to get it replaced.
To ensure the longevity of your water heater you need to ensure that common electrical problems such as tripped breaker or a blown fuse is not the reason for the water heater’s failure.
Know the age of your water heater:
The age of your water heater can be the primary reason behind the faults occurring in your system. Hence, it is crucial to know the age of the machine.
To find the age of your water heater, by looking at the serial number printed on the manufacturer’s sticker, usually pasted on the upper surface of your water heater.
If water heater emits rusty water:
If you notice rusty water coming out of your water heater, especially from the hot side piping fitted in your home, you should understand that it is time to get it replaced.
However, if you have fitted a galvanized piping, the rusting may have occurred in the pipes. A few tested ways to avoid replacing a water heater that is functioning correctly is to drain at least five gallons of water from your water heater.
If your water heater makes a rumbling noise:
Sediments starts depositing on the bottom of the water tank, as your heater starts aging. The sediments get heated and reheated, and subsequently hardens. When this occurs, you often hear the rumbling noise. This is again a sign that your water heater as reached the end of its life.
If you notice moisture around your water heater: If you notice moisture forming around your water tank, or you notice a fracture or a small leak around the tank, it means that your water heater has reached its age, and it is finally the time to replace it
The instances mentioned above are the most common signs indicating the need to replace your water heater. Check yours for these signs today, so you can budget the replacement cost and be prepared to replace it rather than have it give out on you suddenly.
When is it Time to Replace My Water Heater?
Manufacturers generally suggest the common life expectancy of your water heater to be between 8-12 years, and it can vary depending on several factors. Some of the common factors include the location of your unit, its design, and quality of installation.
Installation greatly affects the service life of your water heater as it can generate several issues when handled inaccurately. Leaks, plumbing connection problems, and electrical issues can appear right after a defective installation.
They are skilled and highly experienced to set up your new water heater. To set up your water heater effectively, contact our local trained and insured plumbers in Boston. We’re available 24 hours a day, and 7 days a week.
Hot Water Heater Problems: Why is My Water Heater Not Working?
There are certain things you need to know about how to fix a water heater when you’re encountering some problems with it. What can you do when youâ€™re experiencing water heater problems at home?
Well, the most common water heater problems present are usually lack of heat in hot water, burner malfunction, and corrosion. For you to deal with these problems, you must first know how these can be prevented.
You can prevent this from happening by ensuring in the first place that when you hire your plumber, he or she knows the proper dielectric nipples or dielectric unions that your water heater is using.
If they are not aware about this then they might hook a copper to the water heater, which is made of steel, and could possibly create an electrolysis problem. Which means the connection to the water heater will get corroded.
Lack of temperature for water heater
There is this thing called a dip tube inside and it usually introduces the cold water found at the bottom of the tank. If this gets much corroded, it bowls off and will instead introduce cold water at the top of the tank.
Instead of the hot water dispensing, it gets fed off by the cold water and the burner functions are pretty much obsolete.
Newer high-efficiency water heaters
With this kind of water heater, the biggest problem you could probably face with this is the screen not properly cleaned up on a regular period of time.
Once you plug it up, some debris or lean might compose it. This will make the water heater shut itself down due to improper airflow that does not help at all in aiding the combustion.
If you are wondering how often you should check a water heater, the answer is that you should check on it once in a while and look for signs that may indicate a need for repair.
As for your temperature and pressure valve, you need to ensure that this is functioning properly. If this goes into malfunction and over pressure or overheat, the water heater will release this pressure instead to the water heater. Trust me, you don’t want a hot water that scalding hot as it can be very dangerous.
Determine if there is rust present, which could be an indication of a leak in that certain spot.
How Do I Choose an Electric Water Heating System
There are a few factors to consider when choosing which type of Electric Water Heating System would work best for you and your home.
We are spoilt for choice when it comes to manufacturers and design, but not all electric water heaters are the same. In this article we weigh up the differences between the two types of electric water heaters available on the markets.
Types of Electric Water Heating Systems
We mentioned that there are two different types of electric water heaters available on the market, they are Tank-Type systems and Tankless. Let’s have a look at the difference between the two:
Tank Type or Storage Systems
These are the usual electric water heating systems found in homes across the country. Water is stored within the storage tank, where it is constantly heated. Hot water comes from the top of the tank when a faucet is switched on in the home, which is then replaced by cold water than runs through the bottom of the tank.
These are a newer form of Electric Water Heating. Electricity heats water when water flows the complex unit, so there is not tank needed to heat water.
While both systems offer a range of benefits for the homeowner, you need to consider which is right for your home. Some of the main factors to take into consideration include the price of the system you are investing in and installation of the unit.
Consider what the long-term cost of running a specific unit will be and how readily available the energy sources needed to run the unit are. There is also the Energy Factor rating that is used to measure how efficient the electric water heating system will be. Electric heat pump models should start at 2.0 and the higher the EF count, the more efficient the heater will be.
Long Term Cost Effectiveness
There is more to consider than just the initial cost of a unit when you replace an electric water heating system. Long term costs need to be calculated as well and since energy prices can vary, it is important to get a feel for the long term cost with a Cost Calculator.
There are a few websites that allow you to calculate your energy costs based on the amount of hot water you use. These are typically just a guide, but it will give you a great indication on what to expect from your energy bill after installing a new electric water heating system.
Pros and Cons of Tank-Type vs. Tankless Water Heaters
There are a few advantages and disadvantages to any type of Electric Hot Water Heating system that you choose.
Here we list a few of the most common pros and cons for Tank-Type and Tankless heating units:
Tank-Type Water Heaters
These units are inexpensive and are widely available in a variety of sizes suited to your water heating requirements. Installation costs range from $200 to $400 and onwards.
But these units reportedly waste 10% to 15% of energy through radiant heat loss because of the tank.
Tank-Type units run out of hot water when used for extended amounts of time, cutting your shower short with an ice cold blast of water!
The life expectancy for a tank-type unit is between 10 to 15 years
We mentioned EF ratings earlier and the typical EF Rating for an electric Tank-Type water heating system is only 0.67
Tankless units take up little space and can be mounted inside a wall or on the outside of a home.
There is little to no standby energy loss with these units
They are energy efficient and use between 20% to 30% less energy than Tank-Type units.
The drawback is that they can be costly to install.
But the life expectancy of tankless units far surpass that of a tank-type unit by 20 years or more!
The average EF rating for a tankless unit starts at 0.75
The installation of a tankless system costs between $600 to $1000 and more.
What are the Common Hot Water System Repairs in Every Household?
There are many reasons why your water heater is not working properly. Here are a few problems you may experience:
Worn out heating element
Tripped circuit breaker
Pressure Valve Failure/leaks
Water Heater Sediment
Foul Odor caused by bacteria in tank
Rusty Colored Water
Noisy heating elements
Takes too Long to Reheat
Where Can I Get Reliable Hot Water Heater Service?
When getting a new water heater, it has to be coordinated with several factors that will affect its productivity. A unit that is too small will not produce the right amount of water on demand, while a unit that is too large will consume more energy which will cost you more initially and at the same time on your monthly bills.
Also, as setting up a new water heater involves some complicated calculations regarding the flow rate and temperature that needs to supply your home, doing this yourself can mostly be just on presumptions.
Our team has the skills and knowledge to precisely calculate the load size based on the peak hour demands, and the number of people who will use the system at a given time. This way, your water heating system will generate the needed warm water as intended.
A system installed by our specialists will also ensure the longevity of your system. It can be a deciding factor whether you will get the most out of your water heater investment in the coming years. If you want your water heater to last for a long time, having it installed by our experts will guarantee its durability.
Plumbers 911 has experienced technicians and a wide range of heater options to make sure you have hot water when you need it.
Who Can Fix My Water Heater?
With our specialists, you can expect to receive top-notch service. We carefully screen each of our techs to ensure you are serviced by an experienced professional with a clear background and drug test.
Passed Extensive background checks and drug testing
Continue their education
Are available 24/7 for emergencies
Licensed and Insured
Operate clean and organized vans
Wear professional uniforms
Our technicians can help you with:
No Hot Water
Not Enough Hot Water
Pilot will not Light
Pilot light will not stay lit
Water is too Hot
Rusty or black water
Slow Recovery Time
In addition to basic services, Plumbers 911 provides a licensed professional to assess your existing space and install all parts in accordance with local building codes. Your hot water heater will be up and running in no time and you can rest assured that every safety precaution has been taken.
Who to Call for Water Heater Repair
Our highly efficient local plumbers possess the skills and know how on how to systematically install your water heater, eliminating disorganization that is often associated with an amateur setup.
It guarantees that your heating system will work flawlessly and provide you with the right temperature-controlled water.
Rather than hire a sketchy character and be wary the whole time they are in your home, why not hire a trusted and verified professional? All of our techs possess licenses, are fully insured, and have years of experience under their belt.
If you’re worried about the cost, let us put your mind at ease. We research the local market and know the rates offered by our competitors and offer you an even better rate. Our quotes are accurate, and you will never be charged for something you did not agree on beforehand.
Most people take their plumbing system in Boston for granted. It may work fine today, but the next day, something could go wrong. If not properly maintained and promptly fixed, leaks or broken taps can become worse overtime.
The problem gets bigger when we don’t pay attention to things. Sure, it may seem like a small faucet or a few drops of water here and there. But the real concern is: How much water is it wasting? How much money is thrown away?
Plumbing problems, big or small need immediate attention. That’s a fact. As a homeowner, it is also important to know beforehand what to do in case of a plumbing emergency.
Do you know where your home’s water shut-off valve is located? Do you know who to call for help? Do you have basic plumbing tools in case you have to make temporary repairs?
Let us help you tick one off your to-do list. When you need an emergency plumber in Boston, call us! We have the best technicians in the area, and you can be sure that our services are of high-quality and reasonably priced.
We’ve been recommended by hundreds of residents all throughout the Massachusetts, even in you search for Boston plumber in Yelp. Our professional contractors respect your time and property. From plumbing fixtures to heating maintenance, we’ve got you covered.
There is no denying how useful it can be in a kitchen. While it is not completely necessary, this kitchen appliance simply makes cooking and cleaning up less of a hassle.
Unfortunately, despite how often the garbage disposal is used, it is one aspect of a kitchen that is often overlooked and dismissed. A broken disposal unit can cause a block in the drainage system which needless to say can be a costly affair.
#1 – What NOT To Put In Your Garbage Disposal
Below are just three tips to maintain and keep a garbage disposal system in tip-top shape.
1. Run the garbage disposal unit regularly. It is important to regularly use the garbage disposal unit. Turning on the system a few times a day can assure that rust does not build up along the blades of the system. Moreover, running the unit regularly prevents waste from accumulating and building up.
2. Refrain from putting non-biodegradable food into the garbage disposal unit. It is understandable how tempting it is to shove all kinds of garbage into a garbage disposal unit. Not only does it save time, but tossing trash into the unit requires no trash bags and damp paper towels. Unfortunately, a typical garbage disposal system is simply not made to handle non-food materials. Grinding up glass materials, plastic bottles, scrap paper, cigarette butts and grease can cause damage to the garbage disposal unit’s blade and motor.
3. Keep the garbage disposal unit clean. Quite possibly the simplest way to keep a garbage disposal system from breaking down is to clean it every after use if possible. Running the garbage disposal system after pouring a few drops of soap through cold water is a sure-fire way to maintain a perfectly running garbage disposal system.
We can connect you with a 24 hour plumber in MA to work on your plumbing appliances. Check out our service areas, select your city and call us to schedule a service.
Let’s move on to #2, another part of your home that’s mostly taken for granted.. the septic tank!
#2 – What are the Common Problems in Sump Pumps?
Poor maintenance. A sump pump’s condition should be checked quarterly. Otherwise, you will be put through a great ordeal.
A faulty switch is one of the simplest yet equally annoying mechanical issues with sump pumps. To be safe, clean, adjust, and test your unit on a regular basis to check for problems.
A discharge pipe that is blocked or frozen over will result in a damaging backflow when left unrepaired. A grate will prevent clogs. However, since preventing pipes from freezing has never been realistic, it would be better to install an alternate emergency discharge line as back-up.
Installation fails. The absence of a check valve on the discharge pipe, which can result in water backflow. This will have a domino effect of causing your impeller to have a backward rotation that, in turn, loosens the motor shaft. Your unit may seem to function when it really doesn’t.
Failure to drill an air pressure-relief hole in the discharge pipe, specifically in the middle of the check valve and the pump. The absence of this hole results in the overwhelming build-up of air pressure, which forces your unit to exert itself more than it should. This places a toll on its performance and shortens its lifespan.
Old age. In general, a sump pump has a lifespan of seven to ten years. If your unit is nearing its end, symptoms of old age will start appearing. Once they do, make sure to have it assessed by one of our Boston professionals to see if an immediate replacement is necessary.
Loss of power. Really bad storms and lightning usually results in power outages, rendering your sump pump ineffective. To spare your basement from flooding, purchase and install a backup generator to keep your sump pump up and running as needed.
These two plumbing systems are mostly taken for granted because they’re not seen often, so ensure that you get them regularly checked by calling us today! Ditch the thought of calling a Boston budget plumbing company. We have local Boston plumbers that have over 10,000 hours of training and experience — we already know all plumbing problems and solutions!
Now, let’s talk about something that we use on almost a daily basis, #4: the water heater.
Let’s say you just got a new water heater installed…
You decide to jump in quickly to try it, but to your dismay the water is frigid cold. What might be the problem?
Before you snatch up that phone for a refund, you first need to know that these are common problems and they can be fixed.
#3 – Why Isn’t My Water Heater Working?
Here are some common problems you might encounter with your water heater.
Water is cold
If your water heater runs by electricity, and it is not bringing you hot water after being turned on for some time, the problem may be with the water heating component. Try to check if this is the problem and replace it with a new one.
Another problem may be the thermostat, which is the monitoring device. Water that’s too hot or too cold can be the result of this problem.
This is a common problem for water heaters, when water leaks either from the tip or from the bottom of the appliance. Leaks can be caused by a number of various problems like corrosion.
When water sits in the tubes for long periods, sediment and rust builds up. Eventually, these elements create cracks inside the tubes and the tank itself.
There’s not enough water
Another big problem you might encounter is there is not enough water. When this happens, it’s usually the thermostat that has a problem. Check if the device is properly working and consider the actual temperature of the water to what you can see on the gauge.
A clogged vent can also be the cause of the problem. It may change the normal flow of water from the tubing.
Rusty colored water is usually the cause of a dissolved anode rod. An anode rod is the component of the heater that attracts corrosive elements in the water.
If it is defective, it often emits a sulphuric smell caused by rusting and degradation of the metal. If this is the problem, it might be time to change the anode of the water heater.
Eerie and popping noises
When there is an eerie sound emitting from the water heater, it usually is caused by buildup of sediments inside the tank. Remove the sediments by flushing them out and filling the tank with new clean water.
How Will I Know if My Water Heater Needs Replacement?
Listen to clanking or banging noises, which are signs of aging. Typically upon purchase, a residential water heater comes with a five to ten-year warranty. Unless you have made use of it sparingly over the years, it is advisable that you have your water heater replaced after the specified warranty period.
Check for leaks. Beware! A water heater tank that leaks is a potentially major headache. Calling us ASAP for assessment will save your walls, flooring, furniture, and the water heater unit itself. Depending on where the leak is coming from, a professional can assist you in determining whether your unit requires minor repairs or replacement.
Check if the water produced is hot enough or not. If the heating element and thermostat are not the culprits behind the heating failure, then call our licensed Boston experts to troubleshoot your unit. Expert advice is sounder than speculation.If your unit fails to heat water altogether, it’s an indication of repair or replacement, which our skilled and experienced technicians can make an informed decision on. Consider your hot water usage. Relative to your unit’s age, usage is a big factor in its performance. Even when still far from the end of its warranty period, your unit may suffer from premature aging due to the following:
You have a big or growing family. Your area of residence provides only hard water, which results in a buildup of minerals within the tank. This results in a plumbing line obstruction that inhibits your unit’s performance and decreases its life span. If your unit has served its maximum performance to your family in terms of usage, then perhaps it’s high time to let it retire and find a replacement.
If you’re in a situation where the water in your toilet just won’t go down. It might be a headache to watch those things float in the water. But do not worry; here are some DIYs for a clogged toilet.
#4- How Do I Unclog My Toilet?
DIY Method #1. The Plunger
Most clogged toilets just need one special tool – the plunger. A good plunger would have an extension flange on the rubber bell-shaped end. It is created to fit toilets better so you can convey more potency to the plunge.
A poor flush means that your toilet drain is completely plugged and does not drain. A slow drain means that flushed water somewhat fills the bowl but does not clean the waste away. The water level remains high, but normally drains after a couple of minutes.
DIY Method #2. Drain Snake
A drain snake is a long wire coil with a corkscrew-like tip that you lodge into the pipe until it comes into contact with the clog. You then turn the snake clockwise so the head of the wire screws through the clog and disjoints it. Or the rubble winds onto the wire so you can dislodge the clog.
DIY Method #3. Vacuum
You can use a wet and dry vacuum to dislodge anything that is causing the clog. You can also use the vacuum to empty water out of the bowl. Put a piece of cloth or an old towel down to seal around the drain.
Turning on the vacuum and trying to suction the clog can be effective for anything hard that was dropped in the toilet bowl.
DIY Method #4. Dishwashing Liquid and Hot Water
You can squirt a small amount of dishwashing liquid in the bowl, and then pour a pot of hot water in the bowl. Let the mixture sit for a couple of minutes before attempting to flush.
The dishwashing liquid will ease out the waste clogging the drain and hot water will soften the clogged matter. This will make it easy for you to flush the toilet once everything settles in.
DIY Method #5. Baking Soda and Vinegar
Baking soda and vinegar can be effective in dislodging anything that clogs a toilet. A cup of baking soda, a cup of white vinegar, and a kettle of hot water poured into the bowl will work instantly to flush the toilet clean.
Then, #6 — Your drains..
If you’ve been standing there waiting for the drain to flush the water out but it’s taking far too long.
This is an initial sign that the toilet or sink could be facing a clogged drain. Basically, if you are cautious of what goes down on your drains, you really shouldn’t clean and clear them of debris recurrently.
The following maintenance is needed to prevent a clogged drain that can be a problem in the future. Some can be done once a week and some about once a month.
#5- How Do You Keep Drains Clog Free?
Once a week maintenance tips:
Bring the pop-up stoppers up in the bathroom sink to get rid of trapped debris, put in in the trash and wash the stopper and put it back in the drain.
Take out the drain cover from the shower of the bathtub drain and use a bent wire or hair catching brush to remove debris that might have collected there.
Once a month maintenance tips:
Clean and clear your waste disposal with a stiff disposer brush or mix a few cups of ice and table salt. This will help remove grease buildup and slime off the sides of the disposer. Flush it with cold water added with lemon to deodorize.
For bathtub maintenance, pull out the overflow plate, and bring the pop-up handle up to grasp the rocker arm. Get rid of accumulated debris and wash thoroughly before setting it back.
It is also advisable to use a good cleaner to protect all the drains in your home. A good cleaner has to be non-corrosive and biodegradable so it won’t deteriorate your home plumbing system. It is better to use a nature friendly cleaner than chemical ones as it can be safe to your plumbing system and your family. Drain cleaning in Boston is one of our expertise, call us for help!
To clean your drains effectively, you can use baking soda and vinegar. This is a great way to help eliminate a slow-moving drain.
To unclog a drain with baking soda and vinegar, use the following tips
1. Let a pot of boiling water run down through the drain.
2. Throw in about half a cup of baking soda. Let it sit for a couple of minutes.
3. Then, pour in a mixture of a cup of vinegar and a cup of hot water.
4. Cover the drain with the plug and let it sit for 5-10 mins.
5. Flush with boiling water.
Step 1. Inspect the openings.
Probe the sink for openings and their distance together. Bathroom faucets, in particular, have two handles that may be connected to the spout to form a single unit, or they may be set up apart. This information will be helpful for proper faucet installation or replacement.
Step 2. Turn off the water supply.
There are generally two valves for water supply, one for hot water and another for cold. Turn them off by twisting the valves clockwise to stop water from running in the tubes.
Step 3. Put the faucet replacement in position.
For proper faucet installation:
– Start by positioning the gasket and the faucet on the sink.
– From beneath the sink, thread the mounting nuts into the shanks. Make sure that the flat, wide side part of the mounting nut is up.
– Screw the mounting nuts tight but not too tight to damage it or make it difficult for future replacements.
Step 4. Connect the water supply.
Water is typically supplied by the water-supply tubes. To connect it properly, make sure you take note of the following steps.
Cover the threads of the water supply valve with plumbers tape.
Thread the nut into the shut-off valve and secure with a wrench.
Wrap the faucet shanks threads with plumbers tape and thread the water supply nut against the faucet shanks.
Secure the nut with a wrench.
Step 5. Clean the faucet by flushing.
Make sure that the water supply is clean by running water into the faucet to flush trapped debris off of it. Trapped debris can impair the sealing surfaces inside the faucet and trigger leaks.
Open the water supply valves beneath the sink.
Let water run for 15 seconds to remove residues and trapped particles off the tube.
We’ve covered a whole lot of topics in this blog post, and we hope that you now which one will save you loads of dollars in the end?
However, the decision will always be up to you. Just remember to contact us for any of your plumbing repairs, big or small, because we have licensed, insured and certified Boston contractors on standby, 24/7.
Watch the video below to see why you need to eliminate sub-standard plumbing services and only hire reliable plumbing experts in Boston.
The first step to becoming a responsible homeowner is having a good idea about basic plumbing tips. Plumbing is one thing where you might need emergency service anytime. Imagine if you discover a heavy leakage in your waterline early morning or a flooded bathroom late at night? There are plumbing companies in Overland Park that offer emergency solutions but it’s also good for you to know the basics. One an issue has already manifested, you can get in touch with a plumbing service to handle the situation.
What should you know about emergency plumbing?
An emergency plumbing is a bit different from routine checks and here are their specialities:
There are a few things that you cannot mend – Some plumbing problems require instant repairs. Some issues that are minor can be handled very easily but when things get out of control, you need an emergency service.
They offer a wide range of service – You must know when to call an emergency plumber in Overland Park. Some of the services they offer instantly at any hour include gas leakage, running toilets, burst pipes and sewage problems. Any problem that might cause harm to your health and damage your property is an emergency.
Get them anytime – Routine plumbers are not available at odd hours and you might discover a problem even a 3 am or on weekends. The day and the time of day do not matter; they will come to rescue you. Just give a call and they would arrive as soon as they can.
Definitely bit more expensive than routine services – You must not hesitate to pay something extra for premium service. A team of plumbers coming to rescue you at wee hours and mending all complicated issues deserves more payment.
Helpful emergency plumbing tips
A broken pipe or water leakage – It’s very important to take a note of all the shut-off valves that are responsible for managing the water supply. Do an inspection of your kitchen sink, water heaters, toilet papers, heating systems, tubs and other all other appliances. Ask the plumber working at your place about the stop valves. If needed, seek information from a professional, this will boost your confidence.
Repairing broken pipe yourself – Your pipe is broken and it’s a sheer emergency but before the plumber arrives, try managing yourself. Arrest the water from getting to the broken point of pipe, turn off the valve. If you do not find any shut-off valves just turn off the main valve. Rest the plumber can handle upon arrival.
Why do you need a professional emergency plumber?
Even if you have managed some repairs yourself, it’s important to consult a professional plumbing agency and make use of their tips. They keep on suggesting clients to use strainers to cover the drain openings. What you do is a temporary solution and if those are not mended entirely, it might lead to a further issue in future. Our trained plumbers are experts in finding out the problem and repair it from the root than any patchwork and they have all necessary tools.
You might know a few basic plumbing methods but you are not an expert; so it’s recommended to call a professional when required. Look for references if you are looking for a plumber in your area. Compare the prices and the quality of service and definitely whether they offer emergency service or not.
In times of crisis, remember you have our shoulders to fall back on. Our plumbers are ready to offer assistance and ensure the system is back to normal, functioning properly. This saves you from all hassles and worries; you can really consider it as beneficial. If you are looking for a reliable and trustworthy plumbing service provider for both routine and emergency, we are here for you. Call (816) 384-1295 today!
Homeowners nowadays would want to have all the amenities that could make living easier and more comfortable. Who wouldn’t, right? A hot water heater is one of these amenities as it plays a significant task in making bathing comfortable for all the members of the family. As such, when it conks out, it becomes bothersome for the whole household. It is best to be vigilant in looking for hot water heater problems in Pembroke Pines to prevent further damage and repair expenses.
Watch Out For These Hot Water Heater Problems
Most hot water heater problems can be repaired on your own. Check this list first before heading out to the store to buy a new hot water heating unit. Then again, if you’re not confident with your plumbing skills, you can always contact a licensed Pembroke Pines plumber for help.
Water is too hot
Begin by checking the thermostat. Make sure that it is set correctly. You can adjust it to lower the temperature. If adjusting the temperature does not do the trick, the problem might be with the thermostat itself. This will need to be replaced by a plumbing professional.
Water pressure is low
Examine the shower head if it is clear of sediments or hard water deposits. If it does, get a fine needle that you can insert in the holes. See if this works. Otherwise, locate the reset button and push it. If this still doesn’t resolve the problem, call a hot water heater repair plumber. The problem might be in the thermostat or in another part of the unit.
Leaking water tank
Tighten the bolts on the gaskets surrounding the unit. After that, check the pressure valve. If it still continues to leak, it would be better to buy a new water heating unit especially if this current unit is old. The maximum life span of a hot water heater is 10 to 15 years only. An old heater is most likely to leak because of rusting or wear and tear.
Noisy hot water heater
Drain your hot water heater’s tank first. Then, examine the insides of the tank if there are rusted areas. If there are signs of rusting in some parts, make sure that they are replaced. Water heater units with dirty water coming out of the shower can also be fixed with simple flushing out of water. Remember also to refrain from leaving the hot water heater on for a long time to prevent it from overheating.
Let Plumbers 911 Take Care of Hot Water Heater Problems in Pembroke Pines
The key to having a trouble-free hot water heater unit is routine maintenance. It is still better to be pro-active and to prevent problems by contacting a licensed Pembroke Pines plumber to perform regular check-ups on your hot water heater. Call Plumbers 911 at (954) 866-7699 to set an appointment today.
Meanwhile watch this video to know more about Plumbers 911:
About Plumbers 911
Plumbers 911 is a referral service for local plumbing contractors and technicians. We are not a big nation-wide chain of poorly trained “guys with wrenches.” Instead, we have created a network of local plumbing professionals who own their own companies in your community, and know your unique plumbing needs.