Category: Toilet Repair

5 Effective Slow Flushing Toilet Fix Tips for Your Boston Home

Slow Flushing Toilet Fix Guidelines You Need to Know

Toilet repair BostonIsn’t it so annoying to have a weak, swirling toilet that really takes forever before everything goes down the drain? That is, if everything will even go down? More often than not, toilets that flush slow don’t really get rid of all the waste. This is really why you need to know these slow flushing toilet fix tips.

Picture this… The moment you press that lever attached to the tank and then the water in your toilet starts to slowly swirl (which is all it does) without really flushing everything down. Instead, it sometimes backs the water up as if it’s going to overflow before the water slowly goes down again, leaving fragments and residue of waste floating. Disgusting, isn’t it?!

Can you actually live with that? If so, then this blog post is not for you. You may not really care about what’s happening in your toilet drain or maybe you’ll just take action when it starts to overflow on your Poker game with friends on a Saturday night.

Toilet swirls but not flushing ? This can be caused by a lot of reasons. Although some problems can be fixed without even contacting a professional plumber,  some cases could be really intricate.

You may try a DIY remedy for easier tasks but it won’t always guarantee success. For more complicated toilet problems, we strongly suggest that you seek help from our professional technicians.

In This Article We Will Be Covering:

  • Top 6 reasons for a slow flushing toilet
  • How to properly care for your toilet
  • Signs if your toilet needs repair or replacement
  • Significant fix tips in slow flushing toilets

Toilet Trouble in Boston

6 Reasons You Need to Know Why Your Toilet Drains Slowly

  • Low water level – This is in fact the most common cause of why toilets drain very slowly. If for some reason, the water inside the tank is below the level that is recommended, then there will be not enough water to flush all the waste which will only result to swirling or slow flushing. Your toilet tank needs enough water to attain its flushing power to be able to flush everything down the waste line. Check your toilet float. It can be because the arm is overly bent downwards so the tendency is even if the water level isn’t enough yet, it will automatically click the fill valve off when the float rises just a little.
  • Mineral build-up under the toilet rim – The jet holes under your toilet rim can also be clogged with residues or sediments that accumulate over time because of repeated flushing. This causes weak water pressure that comes out of the holes.As time goes by, more and more mineral deposits will accumulate under your toilet rim if this issue will not be resolved. So, chances are, water pressure will worsen and become weaker, thus leading to slow flush. 
  • Clogged drains – Clogged drains can be the cause of your toilet not flushing completely. You might want to consider that you have some blockage through your drain or waste lines especially if you have kids. This can be a serious problem if not addressed promptly. 

Items such as toys, wipes, sanitary napkins, floss, and other materials that are small enough to fit in and can clog your toilet drains. If not resolved immediately, the item that is causing the blockage can go only deeper down the waste line and it will only make matters worse.

  • Damaged toilet bowl – The system inside a toilet bowl operates through pressure. The colon has to be really airtight for it to be able to pump water out of the drain pipe. If the interior colon is somehow damaged or cracked, then there won’t be enough pressure and will only lead to weak flushing. 

This needs immediate action since the interior colon of the flushing system is a little too intricate and must be fixed only by the pros. This probably is not really advisable for people who like doing DIY tasks because it might only cause you bigger problems if you make a mistake.

  • Weak flushing system – The flushing system in your toilet tank wears down over time. Possible moss build-up may happen due to sediments and mineral deposits that come from hard water. This can be the main cause of faulty flushing system since it will reduce the diameter of the pipes which can reduce water flow through the pathways. 
  • Old/defective flapper – The flapper valve is one of the significant part of the flushing system in your toilet tank. It is supposed to open up when toilet is flushed to completely drain out the water and close down when water is emptied in the tank.

However, if the flapper valve does not open completely, this will result into slow flushing.  It may be because of the chain or rubber string that is attached on the plunger connecting the flapper.

This can be loose because of wear and tear or maybe it is too long that it does not pull the flapper enough to make an adequate opening for the water to completely drain. Thus, you’ll have a toilet that flushes slowly and incompletely.

toilet low flush

4 Significant Tips to Proper Toilet Maintenance and Care 

  • Refrain from disposing garbage – Strictly avoid throwing away garbage in your toilet such as wipes, sanitary napkins, toilet paper, dental floss etc. You may think that when you flush these items away, it also goes down the septic tank… Well, think again.

Some of these items can block the waste pipelines since the pipe circumference decreases overtime due to scum build up around it. Chances are, materials thrown into the toilet get caught up into the pipelines when flushed down. This will result into clogged drains which will eventually lead to water back up or an overflowing toilet. 

  • Immediately fix minor problems – You must not take things lightly and neglect simple problems that may occur. Every minor issue in your toilet requires immediate attention to avoid escalation. This will also save you from spending too much and will save you from stress.

For example, if you have water running in the toilet bowl , immediately check the flapper if it is totally sealed when closed. You can use some dye or food coloring. Put a few drops in the toilet tank. Wait for a few minutes and if you see the color coming out of water in your bowl, it means the flapper is already defective and it needs replacing. 

  • Avoid using harmful chemicals – When cleaning your toilet bowl and tank., avoid using harmful chemicals that may cause corrosion. This might result into interfering with the water pressure when flushing or when filling the tank. 

You can use light toilet cleaning chemicals or better yet use the most natural way, baking soda and vinegar. Sprinkle one cup of baking soda into the toilet and then pour one cup of household vinegar into the bowl. Let it stay for 30 minutes and then scrub with a toilet brush. 

  • Conduct regular inspections – It will definitely make things easier for you if you make a regular inspection of your toilet. Checking and repairing minor things such as small leaks or blockages will ensure that your toilet will always function well. Whether you DIY the maintenance or you hire one of our Boston plumbing technicians to do the inspection, the objective is for you to avoid spending more in the long run.

Repair Toilet Flush in Boston

7 Important Signs To Watch Out For If You Need to Repair Your Toilet

Toilet Plumbing Problems in BostonPerhaps the most important plumbing fixture or equipment in home is your toilet. It’s one thing we CANNOT live without.  

Toilets have made our modern life so much easier. Imagine if we didn’t have any toilets in this new age, will we ever realize the importance of it?  We would never experience the convenience it gives us now.

Fortunately, most of us were exposed into the culture of having and using toilets to dispose of our wastes properly but what if your toilet malfunctions? What if you have a slow draining toilet? How will you know?  Here are the tell-tale signs:

  • Clogs more often – If you know how to take good care of your toilet, you’ll only experience occasional blockage or you may never experience any blockage at all. On the other hand, if you find that your toilet clogs more than once a week, then you must have a more serious problem.

You must have a defective flushing system or there might be a blockage somewhere in your waste pipeline. The parts in the flushing system will eventually be worn out overtime but either way, you still need to address these problems.

Either you hire a professional plumbing contractor to repair the damage in your flushing system or have him dislodge the blockage.

  • Your toilet has a weak flush – If your toilet only swirls when you flush and the water does not even go down, then there must be something wrong with the flushing mechanism. You need a valve replacement and you need to get the right fit.

If you know DIY toilet repairs and you have experienced this kind of issue before and were able to resolve it, then it’s okay for you to do the replacing of the valve. Otherwise, let our techs do the work for you.

  • Tank does not refill with water – After flushing, if the tank or toilet does not refill with water, most probably the fill valve is defective already and you might need to replace it. In this case, you must be sure to get the correct size to be able to install the valve correctly.

Also, you might want to consider checking the flapper if it closes properly after flushing the toilet. If you hear water running after flushing and it won’t stop, most probably the flapper isn’t sealed so there is water going down the drain. We suggest that you replace the flapper to ensure that every after flush it will shut close and it won’t allow any water to find its way down the drain.

  • Standing water around toilet base – Standing water indicates that you have a toilet leak. It could probably be around the seal. This needs to have a seal replacement in order to stop the leak.

Call us to fix the problem. This is to ensure that re-sealing it will be done correctly because if there are parts that will be left unsealed, then the problem might get worse and you wouldn’t want to be spending more for a job that was supposed to be done only once.

  • Water leaking out of toilet cracks – Water leaks don’t always come from the seal around the toilet base. Sometimes it can come from the cracks of the porcelain around the tank or the bowl.

Clean your toilet bowl or toilet tank outside and check if there are any stains or deposit build up around the porcelain or if you see any parts in the surface that is moist. If so, your toilet of tank definitely has cracks and water is leaking out.

Depending on the severity of the leak, if there are chunks porcelain that were detached, then we would recommend that you replace your toilet with a brand new one.

  • Toilet runs constantly – In most cases, the problem comes from the flapper when it is not sealed properly after flushing. Just replace the flapper with a new one then usually it will solve the problem.

However, the problem may also come from the float. If the float does not stop the water from filling, meaning if it fails to shut off the fill valve the waterwill overflow and will continue running.

The solution may be just adjusting the rod that connects the float to the fill valve and slightly bend it downwards so that it shuts off the valve when water rises enough. If the problem still continues, then maybe you should call our Boston MA plumbers to address the issue.

  • Corrosion on metal parts – If your toilet is showing signs of rust and corrosion it’s metal parts then it means that your toilet has worn out. Wear and tear may only show on certain parts so, all you need to do is only to replace those old components with new ones.

However, if you see widespread rust and corrosion then we recommend that you replace your entire toilet to save you from escalated problems in the future. 

Slow Flushing Toilet in Boston

5 Effective Slow Flushing Toilet Fix Tips

Boston Toilet Long FlushToilets have absolutely significant roles in every household. This may be the one thing you may never live without. Toilets are the main lavatory equipment that properly disposes off wastes. On the other hand, this can also be the source of every house owner’s head ache.

When your toilet becomes defective overtime due to wear and tear and you tend to delay inspections and repairs… Chances are, you’ll have bigger and more complicated problems with your toilet.

You may have recurring problems and this will potentially drill a hole in your pocket. So, we strongly urge you to have a regular inspection and never ignore first signs of toilet problems. Bear in mind that there are toilet issues that are intricate and only professional plumbers can solve.

However, we have list down below some important DIY solutions to help you address your toilet’s issues immediately to avoid bigger problems in the future and more importantly to avoid spending more. So, read on and enjoy!

  • Sufficient water in tank – The problem may be because you simply need to adjust the float higher than usual in the toilet tank so the level of the water will increase as well. You may need to bend the rod attached to the float upwards just a little bit, allowing the water to go higher than the usual.

However, be extra careful when adjusting the float rod or bending it as this is attached to the fill valve. The fill valve is where the water comes out to fill the toilet tank. Chances are, you might have a bigger problem if you damage the fill valve because the water will continuously flow and won’t shut off.

  • Working flapper – The flapper is the one responsible for draining your toilet tank. It needs to have enough opening space once you flush the toilet in order to drain the water.

If there is not enough space or if the flapper does not really open enough the water that will drain into the toilet bowl will be inadequate. You need to simply check the chain or rubber that is connecting the flapper and the toilet plunger. You need to make sure that it has the right length to provide enough opening space for the water to drain when the flapper lifts.

  • Trap must be clear – A toilet can be clogged when there is an obstruction through the trap or the vent pipeline which are easy to check.

Ensure that your trap clear of any obstructions. Overtime, if you or you allow people in your household to dispose of materials that are non-biodegradable or items such as toys, wipes, sanitary napkins, floss, and other materials – That can definitely block your drains.

The first thing that you should do is fill a pail one to two gallons of water, then pour everything into the toilet. If your toilet only swirls but does not flush then the blockage is still there. Try using a plunger to suck up the blockage or probably use a snake if it still does not work — That is how to unclog a toilet fast!

  • No obstruction in vent pipe – This is the one that protrudes from the roof of your house by about 30 cm or a foot. This measures about five to eight centimeters or two to three inches in diameter. This is located on top of where your toilet is placed.

Just run a plumber’s snake through the pipe and you can also pour water in it with an extended nozzle or you can also use water pressure in order to flush out the blockage.

  • No blockage around rim – You may locate calcium or other mineral build up under the toilet’s rim after sometime which may be the cause of slow flushing since water from the tank is obstructed by the blockage even if it has enough pressure.

If this is the case, you can use a toilet cleaner that can help dissolve mineral build up. Just follow these simple steps.

  1. Turn of the supply of water
  2. Drain your toilet tank
  3. Open and hold the flapper
  4. Pour ¼ liter of your toilet into the flush valve
  5. Let is stay for 60 minutes
  6. Quickly seal the flapper
  7. Turn on water supply
  8. Flush your toilet 2-3 times to wash down cleaner
  9. You can do it again when needed

Choose a Reliable Plumbing Company in Boston That Can Fix Your Slow Flushing Toilet

So, just remember these helpful tips and chances are you’ll never go wrong. Bear in mind that the faster you act, the lesser chance of you to have bigger toilet problems and it will not only save you from spending too much but it will absolutely save you from a lot of stress. Proper maintenance is the key to having a good plumbing system in your household.

For more intricate low toilet flush problems, we recommend that you leave it to the experts. Trust only a reliable plumbing company that’s been serving people for years now.

We are Plumbers 911 and our plumbers have over 10,000 hours of training and they are all licensed. Backed by years of experience, with high-end tools and top of the line equipment, all our plumbing experts are bonded and insured.

Remember, for toilet leaks, slow flushing toilets or any plumbing issues that you think is impossible to be solved, call Plumbers 911 Boston now and schedule a thorough plumbing check-up. It is definitely cheaper than getting hit with a huge repair bill. 

We’ll flush all your plumbing worries down the drain!

Watch this video to know more about Plumbers 911 and our emergency plumbing service!

Posted on: February 26, 2019

Six Frequent Toilet Plumbing Problems Experienced by Independence MO Residents

Worry-free Toilet Repair from Your Independence Plumber

toilet repair Independence MOIn your Missouri home, there are some things that just have to work reliably. You need your oven for cooking, the smoke alarm for safety, and without the lights, you may as well go to bed when the sun goes down.

However, of all the fixtures in a home, there is one that MUST work reliably every time: the toilet. Unfortunately, there are quite a few things that can go wrong with a toilet.

The toilet is a durable plumbing fixture that may last for years or decades even. However, we all know that toilet problems are the most terrible plumbing issues for homeowners. Even the bravest of men dread the very thought of unclogging the throne — err the toilet.

But then again, that’s only one plumbing problem amongst the many that you’d have to deal with. There’s still a lot more that you need to watch out for and that is why knowledge, familiarity and basic plumbing skills are important. Check out these tips that will come in handy during toilet repairs.

In this article, we will be covering:

  • Clearing a clogged toilet 
  • Troubleshooting toilet issues like ghost flushing, weak flushing, toilet leaks, etc
  • How to repair a leaking toile
  • Toilet repair noise and what to do when your toilet makes noise when flushing
  • Weird toilet flushing sounds – what do they mean?
  • How to repair a toilet flange
  • How to replace your toilet flange

Clogged Toilet Fix

Licensed Plumber for Clogged Toilets in IndependenceIt seems like clogged toilets are the most unbearable of all plumbing emergencies we can ever encounter at home. Though such problems provide lesser inconvenience as that of a burst pipe or a leaky hot water heater, they are, on the other hand, messy and gross to handle.

Who would ever want to deal with the toilet, eh? Luckily for us, if it’s not that hard to unclog the john.  Do you know how to unclog a toilet the natural way,without the use of chemical cleaners?

Clearing a Clogged Toilet

  • Boiling Hot Water
    For minor clogs, the use of boiling hot water generally solves the problem. Just pour a bucket of water into the toilet, making sure that the motion is speedy and yet not so fast for the john to overflow. If a bucket doesn’t get rid of the issue, try another gallon or two.
  • Baking Soda And Vinegar
    If boiling water doesn’t turn out as your bathroom superhero, get your good old baking soda and vinegar out of the kitchen cupboard! It’s time to do some cooking — errr unclogging — using these common ingredients that we’re pretty sure you always have at home.Now pour a cup of baking soda into the toilet. Follow it up with a cup of vinegar. When the two ingredients combine, they will create a fizzing reaction. Once done, check if the toilet is back to working condition again. If not, let’s try another method!
  • Boiling Water And Detergent
    Try using your favorite dish detergent to remove the clog. Just pour a cup of it into the toilet to lubricate the drainpipes. Once your water has boiled, pour the entire kettle into the john. Now double check the result. Still clogged? Move on to the next one below.
  • The Plunger
    If lubricating the drainpipes still isn’t enough, go get your handy dandy plunger. Position it right into the toilet’s drain hole. Plunge in a steady, consistent yet fast pace. You may also plunge as you flush your toilet to give it more draining action. Repeat the process for about 15 times and check if the problem is taken care of.
  • The Snake
    If your ceramic throne is still not functioning well, you’ll have to get down and dirty. Wear rubber gloves to keep your hands clean. Get your snake or auger, insert it into the toilet drain and move the crank clockwise until the tool touches onto something.When it does, keep on pushing the cable further to break the clog into smaller pieces. You’ll know you’re done snaking around when the wire already moves freely inside the drain. Slowly pull it out and dispose of any waste material inside a bucket or a similar container.

Six Frequent Toilet Plumbing Problems

Troubleshooting Toilet Issues

Ghost Flushing
This isn’t a rare toilet problem. Many homeowners experience phantom flushing which involves the presence of sound similar to when a toilet is flushed. What’s inconvenient about this is that the fixture will intermittently make that flushing sound even when no one’s using it.

What causes the problem could be a damaged flapper or a bad flapper seat. The malfunction results to a leak between the tank and the bowl, therefore making water leak and causing the strange reverberation which can strike anytime.

To fix this plumbing problem, the flapper seat must be cleaned or replaced when it’s already too worn out to work.

toilet problems and repairs Independence MOWeak Flushing
Weak flushing is another problem that you have to be ready for. There are times when you’ll notice that waste materials take a long time to get flushed — even when you only peed.

Such a problem may be caused by clogged jet holes. Just get a coat-hanger and poke through those holes to get rid of the sediments and mineral deposits that have accumulated in there. Be extra careful so you won’t scratch the bowl.

Toilet Leaks When Flushed
If you ever hear water trickling into the toilet tank, there’s probably a problem with the supply lines, the float, the refill tube, the ballcock or the inlet valve. This issue is caused by a leak somewhere in the assembly or a component that should be adjusted.

To fix the leak, make sure that the float will stick and that the refill tube isn’t installed too far into the overflow tube. Remember that the refill tube should only go as far as a quarter of an inch below the overflow tube.

Make the necessary adjustments and if these parts won’t get fixed, the only solution left is to replace them.

fixing the toilet Independence MOLeaking Seals
If it leaks somewhere at the base or between the tank and the bowl, you’ll have to check the seals. A leak between the tank and the bowl will result to water shooting from this area.

A leak at the base will cause a forever wet bathroom floor and sooner or later, a wobbly toilet. Tighten the seals and if they’re already worn out, replace them.

Clogs and Toilet Overflowing
Clogs are the most common toilet problems experienced by property owners. It appears that the more the toilets are used and exposed to different waste substances, the more they get clogged.

Always have a cup plunger ready in case blockages occur. If the plunger won’t do the trick, rely on a plumbing snake. These two are the most efficient plumbing tools that you can use to eradicate stubborn clogs. 

clogged toilet repair IndependenceHow to Repair a Leaking Toilet

Throughout the years of use, you’ll eventually discover that your toilet is leaking. Don’t panic. It has parts that deteriorate as the fixture ages so a simple repair or replacement will solve the problem.

But before you perform the necessary repair, it is important that you identify the source of the issue accurately. From there, you should be able to discern the best way to stop the water seepage.

To help you diagnose your toilet, here’s a quick and easy-to-understand guide we’ve written just for you! Check out the most common causes of toilet leaks.

  • Worn-out bolts and washers create leaks. There are two large bolts that secure the tank to the toilet bowl. Water will flow out of the connection if these components deteriorate or get worn out.
  • There’s also a gasket that’s installed between the tank and the toilet bowl. This measures three inches and is responsible for creating a seal between the two toilet parts. If the gasket corrodes, the tank will leak because there will be nothing to support the nuts, bolts and washers in this part.
  • The toilet tank is a container that holds the water used for flushing. Sometimes, objects fall to the tank that cause cracks. If these are not repaired immediately, they will only get bigger and result to leaks.
  • The tank has a float assembly inside. It is a set of components that give the fixture its flushing feature. However, when the assembly gets damaged or malfunctions, the flow of water out of the toilet tank will be continuous. Thus, the tank will overflow and cause leaks.
  • Another culprit is a loose water supply pipe. If this supply pipe becomes loose, cracks or breaks, leaks will surely develop.
  • Speaking of tubes, there’s an overflow tube inside the tank. This component is responsible for letting water out of the tank to prevent overflow. So when this tube gets clogged, you should expect the tank to get totally filled up and water to flow out of the container non-stop.
  • Aside from getting loose or breaking, the supply pipe may also get corroded. When they do, water will flow out continuously.
  • Like the tank, the toilet bowl is also vulnerable to cracking. Once you notice that your toilet bowl is already damaged, it must be replaced immediately not only to avoid leaks but also to prevent accidents.
  • Another essential component of the toilet is the fill valve. When it fails to work as efficiently as it should, the tank won’t be watertight anymore. That said, have this part replaced immediately when it’s already broken.
  • When the leak comes from the base of the toilet, it must be due to a damaged or worn out toilet flange. As usual, this part must be replaced with a new one that will keep the connection tight and leak-free.

Toilet Repair Noise: What To Do When Your Toilet Makes Noise After Flushing

Independence MO toilet flush repairAside from getting clogged, we’re pretty sure that you don’t want your toilets to make weird sounds that might scare the hell out of you in the middle of the night. The only problem is, these sounds cannot be avoided especially when you have an old toilet bowl.

Just like other plumbing fixtures, your toilets have parts that wear out and get damaged over time. And when they do, weird sounds reverberate from them.

Now there are several types of sounds that you might encounter but if it’s specifically making a loud reverberation, much like a foghorn, such a problem may result from the ballcock assembly’s loose washer or a ballcock that isn’t perfectly sealed.

Check out this easy DIY Guide:

  • Remove the toilet tank’s cover and flush the bowl. If you discover that the valve makes the noise, try to resolve the issue by lifting the float ball up. If doing so gets rid of the noise, it just confirms that there’s a loose or damaged washer in the ballcock assembly
  • To fix this problem, first shut off the water supply and flush the tank.
  • When you’re done, locate three screws that are supposedly situated right on top of the fill valve. You’ll have to disassemble the valve assembly so start by removing the screws using your screwdriver. Lift the ball and armature. Finally, carefully lift the flush valve and get it out of the tank.
  • Remove the washer that you’ll finally access at the bottom of the flush valve. Replace it with a new washer. Put the assembly back in place and turn the water supply on again. Test if the sound has been removed. Otherwise, proceed with the next step.
  • Check the valve and make sure that it is sealed. If it’s not, you’ll need to replace it as well. Turn the water supply off again before doing the repair.
  • Flush the tank and scoop out any excess water. You may also use a sponge to absorb the water at the bottom of the tank.
  • After this, proceed by detaching the water supply line from the toilet’s valve connector which is found right under the tank. Loosen the locknut of the toilet valve with the use of your pliers. Remove the nut screw and lift the worn out valve out of the tank.
  • Place a new valve and adjust the water fill level. Screw the toilet valve’s locknut again and tighten it with your pliers.
  • Finally, reconnect the water supply line to the toilet’s valve connector. Turn the water supply on and let the tank fill. Make sure that the water level is an inch above the overflow tube. Flush the toilet again and check if the problem has been fixed.

Repair Toilet Flush: What’s That Weird Sound?

Here are some troubleshooting tips when identifying toilet problems based on flush sounds:

  • Phantom flushing means that the toilet is creating a flushing sound even when there’s no one using it. This can be due to water waste that’s brought about by a leak somewhere. Find the leak and fix it.
  • Weird sound after flushing that usually lasts more than a minute may indicate a pressure issue or restricted water flow. Try adjusting your pressure valve. If it doesn’t get rid of the noise, open the tank and lift the float. Then, if the issue is resolved, try replacing the float.
  • A “cchhhhh” toilet flush sound that occurs sporadically can be a sign of a flapper problem. If the flapper is worn out, an outflow ensues and the toilet tries its best to stabilize the water level, thus creating this sound. Replace the flapper.
  • If it is having gurgling sounds while it’s refilling, there’s a big chance of the water flow not becoming uneven. Adjust the valve to reduce the supply of water to the tank.

how to replace a toilet flangeHow to Repair a Toilet Flange

Is your toilet squeaky or wobbly? Maybe you need to replace the flange! Over years of use, it is just normal for the toilet flange to deteriorate or get a bit unfastened since it’s always exposed to water.

However, it’s not the easiest plumbing project especially if you’re not a skilled plumber. But as they say, great skills develop from experience. Before you get your plumbing kit and dive into the project right then and there, familiarize yourself first with the flange and its function in your toilet

The flange is necessary as it connects and secures the toilet to the drainpipe in the floor. Without it, your toilet will not stay secured in its place and water or even waste will seep out.

Now when that happens, you should prepare yourself for major cleaning! That being said, you should attend to the problem right away once your toilet bowl gets wobbly. So how do you fix or repair a broken flange? Read this step-by-step guide to learn how!

Your toilet flange has a metal or plastic ring holding the toilet to the floor.  It is important because it secures the toilet bowl to the floor and makes the connection to the drain pipe leak-free. You’ll notice that there are holes at the sides of the flange. These holes are where the bolts go through in order to keep the toilet bowl steady.

When this breaks, your toilet can’t be used.  You might also discover that the bowl is a little bit wobbly.   If you encounter a rocking toilet, well, that means your flange is no longer holding it.

There will come a time that you’ll see water pooling at the base of your ceramic throne. These signs indicate that the toilet flange is already worn out.

Replacing it isn’t as easy as you think.  You can purchase repair plates that fix some breaks within the ring or repair rings to cover the entire flange.

Here’s How You Can Replace Your Toilet Flange

  1. Turn the water supply valve of the toilet off to prevent filling up the tank. Now empty the tank by flushing the toilet. You can use a sponge or scoop the remaining water out of the tank. Just ensure that it’s completely empty.
  2. Unscrew the nuts and then loosen the bolts that secure the toilet bowl to the floor. Afterward, break the wax seal that connect the fixture to the flange. When you’re done removing the wax seal, you should be able to remove the bowl. Set it carefully aside and make sure that you’ll put it on top of a towel or rags to prevent it from falling sideways or breaking.
  3. Clean the area where the new flange will be installed. The old wax should be removed with the use of a putty knife or any similar substitute. Guarantee that the area is completely clean to make the new connection leak-free.
  4. If the old toilet flange is not broken or cracked, you can still use it. Otherwise, you’ll have to replace it. If it’s not broken, the leak may be due to loose bolts and nuts. Tighten these parts and re-install the fixture. Check for leaks.
  5. If the flange is damaged, you can get a spanner flange first. It’s a semi-circle part of the flange that can be replaced. You should just unscrew it, remove the bolts and install the replacement in place. Drill the spanner flange to the floor to secure the connection.
  6. Now if the damage is severe and the entire flange is broken, you can just replace the old flange. Clean the installation area; pour the concrete in and let tit set. Put the new flange on top of the concrete and screw it in place.
  7. Put the wax gasket down on the flange. Guarantee that it’s aligned with the flange and the toilet to make the connection leak-free.
  8. Reinstall the toilet bowl and tighten the bolts. Connect the supply line to the tank and turn the water supply valve on. Refill the tank and flush the bowl. Check for leaks.

 Call Plumbers 911 Today

From toilet tank installation to any kind of fixture or toilet problems, give us a call today! We have the most reliable Independence plumbers in the Missouri area. We are available 24 hours a day, 7 days a week! Call us today for immediate assistance!

Posted on: December 30, 2018

9 Common Toilet Clog Problems and Toilet Troubleshooting DIY Repair Tips for Kansas City Residents

Ahh, toilets. What would we do without them? Ensuring that they are working properly is ideal. But over time, their parts break down leading to common issues.  No matter how strong and durable your toilet is, if you don’t give the proper care that it deserves, it will fail, sooner or later.

The key here is proper maintenance and care.  We all know we shouldn’t flush foreign objects down the toilet, but aside from this, we also need to know how to keep our fixtures in tip top shape.

In This Article, We Will Be Covering:

  • 9 common toilet clog problems that homeowners encounter
  • DIY toilet repair tips
  • Recommended clogged toilet fix remedies for common toilet issues
  • How much will a toilet repair cost
  • Toilet troubleshooting
  • Top common causes of toilet clogs
  • How to fix a toilet that keeps running

9 Common Toilet Plumbing Problems that Homeowners Encounter

There are many things that could go wrong inside your toilet. Here are some of the most common toilet problems you need to know to prepare yourself.

Plumber in Kansas CityHow to Repair a Leaking Toilet

Toilet leaks when flushed? Leaks can come from anywhere, in the supply pipe, at the bottom or the seat of the bowl, inside the bowl, at the supply valve, and many other places inside the toilet.

You will notice these leaks when a pool of water is constantly present in your toilet. Or if you don’t see water on the surface, check your water bill. Is it getting higher and higher every month? If so, there must be a leak somewhere in your toilet’s water supply and discharge system.

If your socks are constantly getting wet, your toilet must have a leak. Toilet leaks are caused by various problems. It might mean that the porcelain has cracked- though this would be apparent if it were true. Most commonly, the wax ring located underneath the toilet may have shifted and became loose.

  • First shut off the water supply to your toilet and flush the water out.
  • Now that the toilet and bowl are empty unhook it from the water supply and unbolt the toilet from the floor.
  • Lift it straight up and place to the side. Now the old wax ring should be perfectly accessible.
  • Remove the old ring and replace it with a new one. They only cost around 4 dollars. Once installed, place the toilet firmly over the new ring and bolt the toilet down securely

Tip: Whenever you work on a toilet, take a few minutes to don a pair of rubber or latex gloves and sanitize the base of the toilet with a disinfectant.

Clogged Toilet

You may also experience a sluggish or weak water discharge every time you flush the toilet bowl. The bowl could have a partial clog or perhaps the clog is somewhere downstream. You know it is clogged when the water goes back into the bowl and the draining is very slow.

Clogged Toilet repair KSDripping and continuous water filling of the tank

When you flush the bowl, the tank will fill up with water automatically. But if you still hear a persistent dripping sound after the tank is full, there is a leak somewhere along the line or the system. Tracing the root cause of this problem can be a bit complicated.

Low water level

After flushing, the tank fills up completely. But when you notice that there’s a considerable drop in the water level sometime after the tank fills up, that means water is leaking out somewhere.

One cause of this problem is a crack in the piping or the interior colon of the bowl. If this is the case, your only recourse is to replace the bowl with a new one.

Suction sounds coming from the sink and tub

When you flush the bowl and you hear gurgling sounds, you probably have a clogged toilet vent pipe. It could be a partial clog or a full clog. You can’t tell the cause of the clog by yourself. You need to get the professional services of a licensed technician to fix the issue.

Toilet Repair Services in Kansas CityGhost Flushing

You’re just getting ready to fall asleep, and you hear the toilet flush. Fear grips your heart as it starts to pound fast- you are the only one home. After a couple seconds, you realize that for some reason, your toilet is flushing all by itself.

This water wasting problem is caused by water leaking from the tank into the bowl. To correct it, simply replace the rubber flapper. To test your toilet for this problem, drop food coloring dye into the tank of your toilet. Avoid using the toilet for 30 min and then check the bowl for any signs of the food coloring dye. If present in the water, you have identified the source of the problem.

Without repairing your toilet flush, this problem can waste up to 200 gallons a day!

Toilet Keeps Running After Flush

You do your business, press the handle and the toilet starts constantly running without stop. This problem is caused by a flapper valve not sealing properly. Check to make sure that nothing is preventing the valve from closing properly.

Then, remove any mineral buildup that is around the seat beneath the valve. A third checkpoint is to ensure the pull chain is the right length and is not holding the valve slightly open.   Repairing a leaky toilet tank flush valve can be tricky, so better leave this to our experts.

DIY Toilet Repair: Toilet Overflowing

You did your business, and your business was too large. You flushed, and now your toilet is filling, and filling and about to overflow. To prevent a wet mess, reach into the tank to lift the fill valve higher. The fill valve looks like a ball floating atop the water. This will stop the flow, allowing you use the plunger to remedy the situation.

An Inefficient Toilet

Did you know that toilets manufactured before 1994 are very inefficient? On average these old toilets use up to 3.6 gallons of water every time you flush. Now this is a problem for your water bill. Compare this to newer toilets that use only 1.6 gallons per flush. Despite the reduced water usage, the newer models have just as strong of a flush as the old.

If you wish to save money on your water bill then you may choose to look for a new toilet. Some models offer a dual flushing system which uses less water for liquid waste and the entire 1.6 gallons for solid waste.

How Much Does a Toilet Repair Cost?

The cost of repairing your toilet largely depends on the type of problem that needs to be corrected.

For budgeting purposes, here are the current going rates for toilet repairs in the United States:

  • Replace toilet hardware $35 – $135 per job
  • Install new toilet $200 – $500 per job
  • Replace toilet wax seal $45 – $160 per job
  • Install new shutoff valve $25 – $65 per job

Please take note that these figures are only the average estimates. Our plumbing technicians will be in a better position to give you the exact cost of your toilet repairs once he has completed his inspection.

Leaving aside the mess and inconvenience caused when a toilet fails spectacularly, even routine problems can be a headache. Clogs, leaks, and broken seats are a pain. Not only that, an inefficient, leaky, or always running toilet can waste water and cause higher utility bills.

Toilet Troubleshooting:  Usual Causes of Toilet Problems

Leaks: There are several places where a toilet can spring a leak. Sometimes the leak will be obvious, but other times, you’ll have to inspect your fixture carefully to determine the source of the pool of water on your bathroom floor.

local plumbing fixSupply Line: This is usually a flexible hose which runs from a valve in the wall or floor and leads to the bottom of the tank. Find the water supply valve, shut off the water, and then drain the tank by flushing the toilet. Unscrew the line from both the valve and the tank. To install the replacement, attach the new hose and hand tighten the locknuts at both ends.

Fill Valve: If the leak is at the fill valve itself, you’ll need to replace the fill valve and its gasket. Again, turn off the water supply and flush the toilet, then use a couple of wrenches to remove the fill valve and gasket. After you install the new parts, turn the water supply back on and make sure there are no leaks. If necessary, tighten it little bit more, maybe a quarter-turn or so.

Other leaks will require more work. If the tank itself is leaking, either it or the spud nut will have to be replaced. To be done safely, the job requires two people to avoid injury when moving the heavy porcelain reservoir.

Of course, the most difficult and time-consuming repair is replacing the wax ring where the toilet meets the drainage pipe. We recommend hiring our highly-qualified team of technicians for best results.

Clogs: Most clogs are fairly easy to fix. A few minutes with a plunger will do the job most of the time. However, there are some things to remember when unclogging a toilet:

  • Never use a coat hanger or other improvised object to remove a clog. You will most likely scratch the bowl.
  • Never use chemical drain cleaners in a toilet.
  • If you have to use an auger to clear the blockage, use a closet auger. They are specially designed for use with toilets.
  • When using a plunger, make sure there is at least some water in the bowl. It will help create a vacuum which will cause enough pressure to release most clogs.

plumbing repairs toilet KSBroken or Loose Toilet Seats:This is a fairly simple repair. Toilet seats are attached to the bowl with two locknuts under the lip of the bowl. Simply unscrew the locknuts and install the new seat. Consider using some inexpensive bushings or a seat stabilizer to keep the seat from sliding around.

Flushing Problems: Do you know how to fix a toilet that won’t flush? Once you find it difficult to flush, it could either be the water supply is limited or there is no water at all, or there a certain blockage in the flush tank obstructing the flow of the water.  

If the case is the latter, you can replace the valve yourself. This can be easily bought in your local hardware or plumbing supplies. Over time, the valve wears out and might need replacement. It is also essential to tighten the handle as it could also be the case.

toilet flush repairOverflow: There are times when the lever or the flush ball has worn out and will cause your tank to overflow. You will notice this because the water continues to flow after you have released the handle or if you still hear water flowing even after flushing. It could also be that the refill valve is trapped with dirt or damaged.

The Non-stop water flow is a different case. You can fix this by moving the float ball as it might probably be sitting too high. Intake assembly toilets has clips attached to the rod, these need to be adjusted to lower the water level.

Leaky Tank: Clean and dry the floor area in the toilet. Once done, put several drops of food color in the bowl and leave it for a few minutes. Check if there is colored water the dry floor earlier. If you notice streaks of colored water then your toilet is probably leaking.

Check the wax ring as it might have dislodged. See if there are loose bolts, tighten them up. In the case that the tank is really cracked, then a replacement is needed.

Water Leaks: Sometimes there are occurrences of flush and handle valve issues. The solution to this is to reposition the flush ball once again. A flush ball sitting too high could cause the water leaks to happen. In the event that a broken valve is causing the problem, might as well replace it.

Condensation and Moisture around the Tank: This is a common scenario during cold weather. Your local hardware store sells insulation for tanks that is quite easy to install.

Top Common Causes of Toilet Clogs in Your Home

Unsolved leaks and clogs in your toilet?  There is a saying that prevention is better than cure, so once you’ve found a solution to your problem, make sure that this does NOT happen again. However, you need to figure out why this happened in the first place.

Here are some common causes of toilet clogs:

Toilet Paper

According to Angie’s list, one of the most reputable US directory websites for local businesses, one of the main culprit is the use of toilet paper!  You may think it’s not a big deal – but it is! This is exactly the case, most especially if you’re using the double ply toilet papers in the market today.  If you have no other choice but to dispose these in your toilet, better use Scott tissue (the single ply ones) than those that are thicker. But overall, it’s best to avoid throwing these in your toilet!

Personal Hygiene Products

You may think flushing down diapers and tampons are excused. Not at all! These come in second in the list.  That includes condoms, Q-Tips, baby wipes, dental floss and sanitary pads. Don’t believe everything you read on the label.  Even if it says “flushable” – do NOT take the risk.

Hair

Okay, so you don’t often find hair on the toilet right? Well, some people have the habit of cleaning their brushes and flushing afterwards.  Doing this tends to clog the toilet when these hair form into clumps. And oh, did we say this also includes pet hair?

Other Objects

Okay, aside from your toddler’s toy car, there are other foreign objects that can get stuck, like your trusty toilet freshener.  You know those tank deodorizers that are hung within the walls of your toilet? If these fall and get stuck once flushed, you will need a plumber’s snake to push it out.

You will definitely need to be more careful with your plumbing system to save you more money from expenses and to prevent future headaches.

How to Fix a Toilet That Keeps Running

Kansas City toilet repairsOkay… there’s water running but it’s not coming from the faucet. You listen closely and it’s coming from — the toilet. Can you imagine how much money and water is wasted if this problem continues?

Not everyone knows how to resolve running toilet problems, so hiring the services of a local Kansas City plumber is the fastest and best method of solving the problem.  

Some people opt to troubleshoot common plumbing issues by themselves.  A number of toilet dilemmas can be fixed easily by carrying out some minor tweaks and adjustments and it’s just a matter of knowing what to do and how to do it.  But before doing so, it is best to figure out the cause of all these before carrying on any solution.

Your Stuck Flapper

In order to fix this toilet malfunction, simply grab the flapper and securely close it in your hand.  Carry out any required adjustments and it should respond well to this approach.

The Intermittent Filling

The solution for intermittent filling differs based on its root cause; however, the most general method of correcting this is by removing the buildup of mineral and cleaning the tank.  You can also simply replace the flapper to directly fix the problem.

Toilet Repair: Your Dysfunctional Flapper

Close the valve of the toilet which is frequently located underneath the toilet tank.  Flush the toilet to verify that it is closed. If the tank refuses to fill up, then this proves that the valve has been successfully closed.

Remove the flapper and the chain and replace it with a new one. Use a finger to remove any mineral you find around the rim of the flapper. Remember to make use of a sponge while replacing the flapper.

If You Need Help Troubleshooting Toilet Issues, Call Plumbers 911

Plumbers 911 makes it easy and affordable to hire the best and most reliable plumbing professionals around. All of our contractors must complete a rigorous screening process to join the ranks of the best in the business.

Each technician has over 10,000 hours of training including toilet tank installation and repair, passing an extensive background check and frequent drug tests. Plumbers 911 only works with the absolute best contractors in the business.

  • The work of each of our professional technicians is backed by guarantee. Our prices are highl y competitive.
  • We pride ourselves on being able to provide the highest quality service at the most affordable prices in town. This is a commitment we make to our customers and to ourselves.
  • Our plumbers are all licensed and trained. They also receive continuing education and frequent training sessions.
  • This allows our plumbers to keep their skills fine-tuned. It also ensures that they are well-trained on the latest appliances, technological advances, codes and regulations, processes and trends.
  • You will want to make sure when you hire a plumber that they are knowledgeable about all recent developments in the industry. In addition to consistent training, our technicians are all very experienced in the real world.
  • Their years of on the job hours and experiences make them the best plumbers available. There is no plumbing service that we don’t do and do well.
  • We don’t want you to just take our word for it though. Our website contains tons of reviews from people all over Kansas who are pleased to have used Plumbers 911 and who plan to use our services again in the future.
  • Browse our reviews and you will find words like outstanding, fantastic, best, dependable, reliable, professional, affordable, knowledgeable and friendly. Those are not our words. Those are the words of our customers.
  • No plumbing job is too large or too small for us. We will complete small jobs with the same smile and professional work ethic that we take to larger projects.
  • We want to make sure that every job we do is done to the best of our ability and that our work surpasses our customer’s expectations, regardless of the size or scope of the work order.

 

 

Posted on: December 3, 2018

Top 6 Residential Plumbing Care Tips for Boston Homeowners

Boston plumbersMost people take their plumbing system in Boston for granted. It may work fine today, but the next day, something could go wrong. If not properly maintained and promptly fixed, leaks or broken taps can become worse overtime. 
 
The problem gets bigger when we don’t pay attention to things. Sure, it may seem like a small faucet or a few drops of water here and there. But the real concern is: How much water is it wasting? How much money is thrown away?
 
Plumbing problems, big or small need immediate attention. That’s a fact. As a homeowner, it is also important to know beforehand what to do in case of a plumbing emergency. 
 
Do you know where your home’s water shut-off valve is located? Do you know who to call for help? Do you have basic plumbing tools in case you have to make temporary repairs?
 
Let us help you tick one off your to-do list. When you need an emergency plumber in Boston, call us! We have the best technicians in the area, and you can be sure that our services are of high-quality and reasonably priced.
 
We’ve been recommended by hundreds of residents all throughout the Massachusetts, even in you search for Boston plumber in Yelp. Our professional contractors respect your time and property. From plumbing fixtures to heating maintenance, we’ve got you covered.
 
First, let’s talk about garbage disposals.
 
There is no denying how useful it can be in a kitchen. While it is not completely necessary, this kitchen appliance simply makes cooking and cleaning up less of a hassle.
 
Unfortunately, despite how often the garbage disposal is used, it is one aspect of a kitchen that is often overlooked and dismissed. A broken disposal unit can cause a block in the drainage system which needless to say can be a costly affair.

#1 – What NOT To Put In Your Garbage Disposal

Below are just three tips to maintain and keep a garbage disposal system in tip-top shape.

1. Run the garbage disposal unit regularly. It is important to regularly use the garbage disposal unit. Turning on the system a few times a day can assure that rust does not build up along the blades of the system. Moreover, running the unit regularly prevents waste from accumulating and building up.

jammed garbage disposal in Boston2. Refrain from putting non-biodegradable food into the garbage disposal unit. It is understandable how tempting it is to shove all kinds of garbage into a garbage disposal unit. Not only does it save time, but tossing trash into the unit requires no trash bags and damp paper towels. Unfortunately, a typical garbage disposal system is simply not made to handle non-food materials. Grinding up glass materials, plastic bottles, scrap paper, cigarette butts and grease can cause damage to the garbage disposal unit’s blade and motor.

3. Keep the garbage disposal unit clean. Quite possibly the simplest way to keep a garbage disposal system from breaking down is to clean it every after use if possible. Running the garbage disposal system after pouring a few drops of soap through cold water is a sure-fire way to maintain a perfectly running garbage disposal system.

We can connect you with a 24 hour plumber in MA to work on your plumbing appliances. Check out our service areas, select your city and call us to schedule a service.

Let’s move on to #2, another part of your home that’s mostly taken for granted.. the septic tank!

 #2 – What are the Common Problems in Sump Pumps?

Poor maintenance. A sump pump’s condition should be checked quarterly. Otherwise, you will be put through a great ordeal.

A faulty switch is one of the simplest yet equally annoying mechanical issues with sump pumps. To be safe, clean, adjust, and test your unit on a regular basis to check for problems.

A discharge pipe that is blocked or frozen over will result in a damaging backflow when left unrepaired. A grate will prevent clogs. However, since preventing pipes from freezing has never been realistic, it would be better to install an alternate emergency discharge line as back-up.

Installation fails. The absence of a check valve on the discharge pipe, which can result in water backflow. This will have a domino effect of causing your impeller to have a backward rotation that, in turn, loosens the motor shaft. Your unit may seem to function when it really doesn’t.

Failure to drill an air pressure-relief hole in the discharge pipe, specifically in the middle of the check valve and the pump. The absence of this hole results in the overwhelming build-up of air pressure, which forces your unit to exert itself more than it should. This places a toll on its performance and shortens its lifespan.

Old age. In general, a sump pump has a lifespan of seven to ten years. If your unit is nearing its end, symptoms of old age will start appearing. Once they do, make sure to have it assessed by one of our Boston professionals to see if an immediate replacement is necessary.

Loss of power. Really bad storms and lightning usually results in power outages, rendering your sump pump ineffective. To spare your basement from flooding, purchase and install a backup generator to keep your sump pump up and running as needed.

These two plumbing systems are mostly taken for granted because they’re not seen often, so ensure that you get them regularly checked by calling us today! Ditch the thought of calling a Boston budget plumbing company. We have local Boston plumbers that have over 10,000 hours of training and experience — we already know all plumbing problems and solutions!

Now, let’s talk about something that we use on almost a daily basis, #4: the water heater.

Let’s say you just got a new water heater installed…

You decide to jump in quickly to try it, but to your dismay the water is frigid cold. What might be the problem?

Before you snatch up that phone for a refund, you first need to know that these are common problems and they can be fixed.

#3 – Why Isn’t My Water Heater Working?

Here are some common problems you might encounter with your water heater.

Water is cold
If your water heater runs by electricity, and it is not bringing you hot water after being turned on for some time, the problem may be with the water heating component. Try to check if this is the problem and replace it with a new one.

Another problem may be the thermostat, which is the monitoring device. Water that’s too hot or too cold can be the result of this problem.

Boston Water Heater Installation ServicesLeaking water
This is a common problem for water heaters, when water leaks either from the tip or from the bottom of the appliance. Leaks can be caused by a number of various problems like corrosion.

When water sits in the tubes for long periods, sediment and rust builds up. Eventually, these elements create cracks inside the tubes and the tank itself.

There’s not enough water
Another big problem you might encounter is there is not enough water. When this happens, it’s usually the thermostat that has a problem. Check if the device is properly working and consider the actual temperature of the water to what you can see on the gauge.

A clogged vent can also be the cause of the problem. It may change the normal flow of water from the tubing.

Rusty water
Rusty colored water is usually the cause of a dissolved anode rod. An anode rod is the component of the heater that attracts corrosive elements in the water.

If it is defective, it often emits a sulphuric smell caused by rusting and degradation of the metal. If this is the problem, it might be time to change the anode of the water heater.

Eerie and popping noises
When there is an eerie sound emitting from the water heater, it usually is caused by buildup of sediments inside the tank. Remove the sediments by flushing them out and filling the tank with new clean water.

How Will I Know if My Water Heater Needs Replacement?

  • Listen to clanking or banging noises, which are signs of aging. Typically upon purchase, a residential water heater comes with a five to ten-year warranty. Unless you have made use of it sparingly over the years, it is advisable that you have your water heater replaced after the specified warranty period.
  • Check for leaks. Beware! A water heater tank that leaks is a potentially major headache. Calling us ASAP for assessment will save your walls, flooring, furniture, and the water heater unit itself. Depending on where the leak is coming from, a professional can assist you in determining whether your unit requires minor repairs or replacement.
  • Check if the water produced is hot enough or not. If the heating element and thermostat are not the culprits behind the heating failure, then call our licensed Boston experts to troubleshoot your unit. Expert advice is sounder than speculation.If your unit fails to heat water altogether, it’s an indication of repair or replacement, which our skilled and experienced technicians can make an informed decision on. Consider your hot water usage. Relative to your unit’s age, usage is a big factor in its performance. Even when still far from the end of its warranty period, your unit may suffer from premature aging due to the following:
  • You have a big or growing family. Your area of residence provides only hard water, which results in a buildup of minerals within the tank. This results in a plumbing line obstruction that inhibits your unit’s performance and decreases its life span. If your unit has served its maximum performance to your family in terms of usage, then perhaps it’s high time to let it retire and find a replacement.

Now for the good stuff: DIY Plumbing with #5 –Your toilet!

If you’re in a situation where the water in your toilet just won’t go down. It might be a headache to watch those things float in the water. But do not worry; here are some DIYs for a clogged toilet.

#4- How Do I Unclog My Toilet?

running toilet problem BostonDIY Method #1. The Plunger
Most clogged toilets just need one special tool – the plunger. A good plunger would have an extension flange on the rubber bell-shaped end. It is created to fit toilets better so you can convey more potency to the plunge.

A poor flush means that your toilet drain is completely plugged and does not drain. A slow drain means that flushed water somewhat fills the bowl but does not clean the waste away. The water level remains high, but normally drains after a couple of minutes.

DIY Method #2. Drain Snake
A drain snake is a long wire coil with a corkscrew-like tip that you lodge into the pipe until it comes into contact with the clog. You then turn the snake clockwise so the head of the wire screws through the clog and disjoints it. Or the rubble winds onto the wire so you can dislodge the clog.

DIY Method #3. Vacuum
You can use a wet and dry vacuum to dislodge anything that is causing the clog. You can also use the vacuum to empty water out of the bowl. Put a piece of cloth or an old towel down to seal around the drain.

Turning on the vacuum and trying to suction the clog can be effective for anything hard that was dropped in the toilet bowl.

DIY Method #4. Dishwashing Liquid and Hot Water
You can squirt a small amount of dishwashing liquid in the bowl, and then pour a pot of hot water in the bowl. Let the mixture sit for a couple of minutes before attempting to flush.

The dishwashing liquid will ease out the waste clogging the drain and hot water will soften the clogged matter. This will make it easy for you to flush the toilet once everything settles in.

DIY Method #5. Baking Soda and Vinegar
Baking soda and vinegar can be effective in dislodging anything that clogs a toilet. A cup of baking soda, a cup of white vinegar, and a kettle of hot water poured into the bowl will work instantly to flush the toilet clean.

Then, #6 — Your drains..

If you’ve been standing there waiting for the drain to flush the water out but it’s taking far too long.

This is an initial sign that the toilet or sink could be facing a clogged drain. Basically, if you are cautious of what goes down on your drains, you really shouldn’t clean and clear them of debris recurrently.

The following maintenance is needed to prevent a clogged drain that can be a problem in the future. Some can be done once a week and some about once a month.

#5- How Do You Keep Drains Clog Free?

Once a week maintenance tips:
Bring the pop-up stoppers up in the bathroom sink to get rid of trapped debris, put in in the trash and wash the stopper and put it back in the drain.

Take out the drain cover from the shower of the bathtub drain and use a bent wire or hair catching brush to remove debris that might have collected there.

Drain Cleaning BostonOnce a month maintenance tips:
Clean and clear your waste disposal with a stiff disposer brush or mix a few cups of ice and table salt. This will help remove grease buildup and slime off the sides of the disposer. Flush it with cold water added with lemon to deodorize.

For bathtub maintenance, pull out the overflow plate, and bring the pop-up handle up to grasp the rocker arm. Get rid of accumulated debris and wash thoroughly before setting it back.

It is also advisable to use a good cleaner to protect all the drains in your home. A good cleaner has to be non-corrosive and biodegradable so it won’t deteriorate your home plumbing system. It is better to use a nature friendly cleaner than chemical ones as it can be safe to your plumbing system and your family. Drain cleaning in Boston is one of our expertise, call us for help!

To clean your drains effectively, you can use baking soda and vinegar. This is a great way to help eliminate a slow-moving drain.

To unclog a drain with baking soda and vinegar, use the following tips

1. Let a pot of boiling water run down through the drain.
2. Throw in about half a cup of baking soda. Let it sit for a couple of minutes.
3. Then, pour in a mixture of a cup of vinegar and a cup of hot water.
4. Cover the drain with the plug and let it sit for 5-10 mins.
5. Flush with boiling water.

Lastly and the most basic: Faucet installation.

#6 – How Do I Install a Faucet?

Step 1. Inspect the openings.
Probe the sink for openings and their distance together. Bathroom faucets, in particular, have two handles that may be connected to the spout to form a single unit, or they may be set up apart. This information will be helpful for proper faucet installation or replacement.

Step 2. Turn off the water supply.
There are generally two valves for water supply, one for hot water and another for cold. Turn them off by twisting the valves clockwise to stop water from running in the tubes.

Step 3. Put the faucet replacement in position.

For proper faucet installation:

– Start by positioning the gasket and the faucet on the sink.
– From beneath the sink, thread the mounting nuts into the shanks. Make sure that the flat, wide side part of the mounting nut is up.
– Screw the mounting nuts tight but not too tight to damage it or make it difficult for future replacements.

Step 4. Connect the water supply.
Water is typically supplied by the water-supply tubes. To connect it properly, make sure you take note of the following steps.
Cover the threads of the water supply valve with plumbers tape.
Thread the nut into the shut-off valve and secure with a wrench.
Wrap the faucet shanks threads with plumbers tape and thread the water supply nut against the faucet shanks.
Secure the nut with a wrench.

Step 5. Clean the faucet by flushing.
Make sure that the water supply is clean by running water into the faucet to flush trapped debris off of it. Trapped debris can impair the sealing surfaces inside the faucet and trigger leaks.
Open the water supply valves beneath the sink.
Let water run for 15 seconds to remove residues and trapped particles off the tube.

We’ve covered a whole lot of topics in this blog post, and we hope that you now which one will save you loads of dollars in the end?

However, the decision will always be up to you. Just remember to contact us for any of your plumbing repairs, big or small, because we have licensed, insured and certified Boston contractors on standby, 24/7.

Watch the video below to see why you need to eliminate sub-standard plumbing services and only hire reliable plumbing experts in Boston.

Posted on: October 18, 2018

8 Signs of Residential Plumbing Problems in Kansas You Can’t Ignore

Residential Plumbing in Kansas CityOne of the most important parts in our household is the plumbing system. Why? Simply because this controls the flow of water in our home. Whether we run water from the tap or flush it down the drain, every plumbing part is placed systematically by professional plumbers to work properly.

Water, as we all know is very important to every individual. In other words, we cannot function well without it. So, we have faucets and showers where we get water for washing, cleaning and drinking. We have toilets to do our daily rituals. These plumbing fixtures are beneficial and it helps us use water accessibly.

Why is it Important to Find Out and Fix the Plumbing Problems in Your Residence?

However, if we neglect to care for our plumbing system properly and overlook small issues, then we are in for a big surprise (not in a good way though!). That’s why plumbing maintenance is imperative. 

It is a good way to know if everything is working perfectly. You can hire licensed plumbers to have a regular check-up or you can also DIY your plumbing issues if you think you are capable enough.

If you fail to maintain or fix any plumbing problems in your home, then chances are you’ll end up paying for more because the damage will worsen overtime. Say for example, a faulty tap may waste a lot of water because of a leak. Every drip adds up. Bear in mind that it only takes 4,000 drips to make one litre of water and that’s wasted water AND money.  Plus, it will eventually worsen as time goes by. 

Some plumbing issues may eventually lead to damaging other plumbing components. Then again, more money to spend. On top of that, it is also possible that other problems may pose a threat to your family’s health and we wouldn’t want that.

In This Article, We Will Be Covering:

  • 8 Signs of Residential Plumbing Problems
  • The Importance of Plumbing Maintenance
  • How to DIY Small Plumbing Repairs
  • How to Maintain Your Plumbing System
  • How to Find The Right Plumbing Contractors

8 Dreadful Signs That Tell You Need to Hire a Kansas Residential Plumbing Expert

Plumbing issues are one of the things we tend to ignore until it’s too late. MostKansas Residential Plumbing people know the basics in troubleshooting such as using a plunger for toilets and applying baking soda plus vinegar for clogged drains. 

However, plumbing problems do not end there. There are things that we (regular people) cannot do-it-ourselves when it comes to more intricate issues.

That’s why these are best not to be ignored. Aside from that, you might go through the trouble of the mess it will bring you and you might also have to shell out a BIGGER amount of money for the repairs of the damage that you didn’t pay attention to.

Say for example, a simple blocked pipe line might start a leak overtime and may lead into bursting pipes in the long run since it was ignored. That would have been an inexpensive plumbing repair if the problem was addressed the earliest time compared to replacing your entire pipeline and also the damage it may cause. 

Read on to find out more about these important signs that you should NOT ignore:

  • Gurgling Sound – If you hear some gurgling sounds whenever you use your toilet,  washing machine or your dishwasher, this might be your first indication that you have a clogged drain.

    When you hear some gurgling sounds even if you are not using your toilet, this is a sign that air is finding its way out through your system and you are most likely to have a backup or overflowing toilet.It’s quite the same thing when you are taking a shower, using the washing machine or using your dishwasher.If you hear some gurgling sounds when using them, you need to stop and observe first before having back up problems and call a trained technician.

  • Running Toilet If you hear water running in your toilet chances are, you have a leak. Fortunately, there are ways to check or locate where the leak is coming from. First, check the plunger by flushing your toilet and make sure that the plunger is properly back in to its place after flushing your toilet.

    If there is still running water, check the float arm inside the tank if it’s properly adjusted.  When water is full it’s supposed to shut off your fill valve. Check if the switch automatically shuts off when the float arm is completely raised.After doing these things and you still hear running water, then you might as well check the flapper.Check if it still works or maybe it needs replacement already.

    This is actually very easy to do. Get a dye or any food coloring and simply add a few drops into the toilet tank (but first make sure that the water in the toilet is clean!)You’ll see the results in just a few seconds.If your flapper is really the culprit, meaning it’s already damaged and it needs to be replaced, then you’ll see the food colouring coming out mixing with the clean water in your toilet.That means you flapper is worn out and you need to replace it ASAP because this will waste a lot of water and later on you will regret paying for a high water bill.

    However, if you are unfamiliar with your toilet tank’s components, it’s best to call in a licensed tech to get the job done.

  • Leaking Pipes If you hear hissing sounds even if nobody is using the toilet or kitchen or perhaps you see some discoloration on your walls, floors or ceilings, then you most probably have a leak coming from your pipes.

    If you really want to be sure that you have a leak, that is easy to determine. Just turn off all faucets and showers in your home. Be sure that  nobody is using the bathroom or kitchen.Then check your water meter if it is still spinning.If so, then you definitely have a leak. Now, locating where the leak is coming from is another story.Leak detection is a plumber’s specialty.  Licensed techs have state of the art tools and equipment to determine where a leak is coming from without causing any damage to your property.  

  • Weak Water Pressure – In most cases, the weakening of water pressure from your kitchen and bathroom taps is because of gunk or scum build up overtime in your faucet’s aerator. 

This is actually very easy to do. You just have to unscrew the aerator from the faucet and brush off the residue with soap and water. When it’s already clean, just screw it back onto the faucet tightly.

However, if this does not change the water pressure coming from your faucet, then the problem may be coming from leaking pipes or clogged water lines. We recommend hiring a certified plumber to address the issue.

  • Water Drains Slow If in case you notice your kitchen or bathroom sinks drain a little too slow than usual, your drains may be clogged. Using mild drain solutions or vinegar with baking soda will probably do the trick.If you follow it up by shoving a plunger onto to the drains, it might suck up the clog or flush it down if it is easy to remove.

That said, if the blockage won’t budge, you might want to consider using a snake drain. However, there is always risk of damaging your drain pipes if they are corroded or brittle already. So, be extra careful when doing this because you might end up spending more for just a simple job.

  • Frozen Pipes – This is something that you surely don’t want to ignore. If your pipes get frozen during the winter, you need to call a 24/7 emergency plumber immediately.Some signs of frozen pipes are: water not running through your pipes anymore, weird gurgling noises once you turn on your faucet or ice on your pipes.

    Never try to thaw the pipes by yourself because this can lead to more damage. This can crack or even burst your pipes if you try to defrost them yourself.To prevent your pipes from freezing, let your taps drip cold water if possible overnight when the temperature drops below freezing, then leave your sink cabinets open to be exposed to warm air.

  • Sewage OdorIf you notice a pungent smell or a really disgusting sewer odor, chances are you have a damaged sewer line or a broken vent. If you have any broken sewer pipes or vents, this could actually be a threat not only to the environment but of course to your family’s health as well.

    It is strongly recommended to contact a certified contractor to address this issue and prevent it from getting worse. Otherwise, you will surely face the consequences later on and it’s going to cause you more $$$. In case you smell something odd that is coming from your sewer lines, act fast and do not ignore.

  • Gas Leak – If in case you smell gas, whether you’re in the kitchen or using your dryer, then you probably have a gas leak.  This is not an issue that you can take for granted since this could be fatal. Your family’s health and life is at risk.

This is a serious matter since you are talking about life and death. Immediately call a gas system professional to address the problem. Remember not to turn on any of your appliances because this could start a spark and will ignite the gas to explode.

Open your windows or doors to release the gas odor from your house while waiting for the professional gas techs to check and fix the problem. 

Residential Plumbing Service in Missouri

Additional Tip: 

You can check the pressure in your house. As much as possible, avoid adding too much stress in your plumbing system and ensure that your water pressure is always at a level that is safe. 

Just check your water pressure by using a gauge. You need to see if the water pressure is too high. If so, you need to repair or probably replace the pressure regulator to ensure that the pressure is in a safe level.

What are Some Vital Guidelines on Plumbing Maintenance?

Proper maintenance is the key to having a good plumbing system in your home.
It is vital to have clean water that flows in and to be able to flush waste out of your home safely.

Drain Trap Repair in Kansas CityThere are a lot of issues that may happen to your pipes, drains, toilets, water heaters and so much more. Leaks in your sink drains for instance, or leaks from your water heaters can be more than just a nuisance. More often than not, they cause mold to grow and structural damage if not fixed immediately.

However, most people tend to disregard small plumbing problems until they become big and serious.

By then, you are left with a possible electrical issues, wood or concrete damage and definitely a huge plumbing problem. On top of that, you still have a huge bill that you have to pay.   These adversities can be avoided if you don’t neglect having proper plumbing maintenance. Remember that by maintaining your plumbing, you can easily identify minor problems and you can resolve it immediately. 

Bathroom:

  • Fix Broken Taps – Immediately fix leaking taps or showers either in your bathroom or kitchen. Although, it may seem insignificant at first, but it will eventually be costly if the damage worsens. Consider also the amount of water wasted if you neglect this for a long time.  Bottomline — while it’s still small, fix it!
  • Declog Your Drains – Hair, soap residue, or any debris that goes down the sink and tub drains will eventually accumulate and will be the cause of blockage. It’s easy to clear out unwanted elements in your drain when it’s still early. You need to do this every few months or when you notice that water slowly goes down the drain.
  • Clear Your Faucet Aerators – Overtime, calcium builds up in your faucet aerator and this can definitely obstruct water flow. You will notice that your water pressure weakens in your faucet or shower — that means, there may already be some calcium build up. Cleaning your aerators regularly by removing them will ensure free flowing water.
  • Repair Any Running Toilets – Checking your toilet on a regular basis will help you discover small problems. Particularly, when you have a running toilet. Overtime, parts of your toilet may wear down and can cause problems.If you notice that your toilet is running even if it is not flushed, there are a few things to consider. Your flapper might need replacement, your fill valve might be defective and it isn’t stopping water from filling or your float arm might not be well adjusted.

Kitchen:

  • Fix Your Sink Leaks – Kitchen sinks are often used in households which can be the cause of leaks coming from taps, sink drains or garbage disposal or any other sink accessories. You have to thoroughly examine your kitchen sink for any leaks or any signs of damage regularly to avoid huge problems in the future.
  • Examine Your Garbage Disposal – More often than not, garbage disposals can be the cause of leaks if it goes unnoticed. You need to check your unit for any signs of problems. Of course, you have to do it with caution or better yet check the recommendations of your manufacturer on how to maintain your unit to be safe.
  • Clean Your Sink Drain – Constantly keep your kitchen sink drain clean by applying natural drain cleaners. If you can use brushes that can reach deep in your drain, the better. It is imperative you keep your drains free from any residues or build-up to keep the water going down the drain fast. 

Water Heater:

  • Settings – You need to set your water heater in an optimal performance. Remember that your water heater works double during the months that are cold, so proper maintenance is the key to prolonging your water heater’s life. Set your water heater at 120 Fahrenheit if you are looking for a top quality performance.  
  • Flush Out – Sediments in your water heater when accumulated can cause corrosion overtime. This reduces your water heater’s efficiency and it will definitely lessen its lifespan. Corrosion can also cause leaks in the long run since it can eat up steel and it will eventually find it’s way out.
  • Test Pressure – Testing the water heater’s pressure must be done with extreme caution. Just release the water heater’s valve by lifting its lever and let it flick back.You’ll notice a burst of hot water through the drain pipe and this indicates that it is working properly. Remember, If your water heater is already five years or older, we suggest that you contact a professional plumber to prevent accidents.

Septic Tank / Sewer:

  • Inspect Regularly – A sewer stoppage or main line blockage is absolutely a huge problem. So, it is better to avoid rather than to go through the problem especially if it worsens. You always have to maintain your septic tank system. You need to have this inspected regularly by a professional if not by you to see if it’s about to overflow already.
  • Septic Tank Pumping – Pumping your septic tank regularly is the most important part of maintaining. This will definitely clean your septic tank and get rid of the water waste and unwanted bacteria in your tank.This can also eliminate or minimize odor (if there is) that comes out through your toilet or drains. However, the schedule of septic tank pumping depends on the size of the septic tank and the frequency of usage.
  • Check Sewer Line – Maintaining your mainline regularly will prevent it from stoppages.You have to be sure that your sewer line is properly working and how frequent stoppages occur.Homes that have trees by their yards may have tree roots that can cause repeating sewer issues. It’s best to schedule a service to snake your sewer for preventative check-up. Watch out for the signs of sewer blockages before it worsens.
    find a local plumber in Chicago to save water

Contact Our Kansas Plumbing Professionals Now!

For your plumbing concerns, contact our local technicians. No matter how small the issue is, you’ll never know if this requires immediate attention. Don’t wait until it’s too late.

You wouldn’t want to be spending a lot of money for huge damages when it could have been only a preventative check-up or a minor plumbing problem that could be fixed with a very reasonable price. 

Residential Plumbing Reviews in Missouri

Why People in Kansas City Prefer Our Services for Their Residential Plumbing Issues

People want to get their money’s worth when shelling out, especially when they have something that they need to get fixed immediately. We always think of our clients’ satisfaction and we make sure that is accomplished every time we visit a home for service and repairs.

Why is that? Because we wouldn’t want to hire somebody that would just make matters worse if we were in our clients’ situation. 

We at Plumbers 911 pride ourselves in taking everything seriously! Solving your plumbing problems is definitely our primary concern. Our team will surely solve all your plumbing problems whether it’s big or small. Bear in mind that we’ve got you covered!

Backed by our multiple years of experience and 10,000 hours of intensive plumbing training, we will deliver quality service for every task that we will handle. All our plumbing contractors are bonded, licensed and insured so you have nothing to worry about. With our top of the line plumbing tools and high-end equipment, our plumbers will get the job done fast and efficiently.

Stop worrying and leave it to us. We will surely flush your plumbing problems down the drain. So, the next time you need a plumbing help for your residential plumbing problem in Kansas City, you only need to call Plumbers 911, where emergency plumbing service is just one click away!

Watch the Video Below on Residential Plumbing

Posted on: September 26, 2018