Category: Toilet Installation

5 Effective Slow Flushing Toilet Fix Tips for Your Boston Home

Slow Flushing Toilet Fix Guidelines You Need to Know

Toilet repair BostonIsn’t it so annoying to have a weak, swirling toilet that really takes forever before everything goes down the drain? That is, if everything will even go down? More often than not, toilets that flush slow don’t really get rid of all the waste. This is really why you need to know these slow flushing toilet fix tips.

Picture this… The moment you press that lever attached to the tank and then the water in your toilet starts to slowly swirl (which is all it does) without really flushing everything down. Instead, it sometimes backs the water up as if it’s going to overflow before the water slowly goes down again, leaving fragments and residue of waste floating. Disgusting, isn’t it?!

Can you actually live with that? If so, then this blog post is not for you. You may not really care about what’s happening in your toilet drain or maybe you’ll just take action when it starts to overflow on your Poker game with friends on a Saturday night.

Toilet swirls but not flushing ? This can be caused by a lot of reasons. Although some problems can be fixed without even contacting a professional plumber,  some cases could be really intricate.

You may try a DIY remedy for easier tasks but it won’t always guarantee success. For more complicated toilet problems, we strongly suggest that you seek help from our professional technicians.

In This Article We Will Be Covering:

  • Top 6 reasons for a slow flushing toilet
  • How to properly care for your toilet
  • Signs if your toilet needs repair or replacement
  • Significant fix tips in slow flushing toilets

Toilet Trouble in Boston

6 Reasons You Need to Know Why Your Toilet Drains Slowly

  • Low water level – This is in fact the most common cause of why toilets drain very slowly. If for some reason, the water inside the tank is below the level that is recommended, then there will be not enough water to flush all the waste which will only result to swirling or slow flushing. Your toilet tank needs enough water to attain its flushing power to be able to flush everything down the waste line. Check your toilet float. It can be because the arm is overly bent downwards so the tendency is even if the water level isn’t enough yet, it will automatically click the fill valve off when the float rises just a little.
  • Mineral build-up under the toilet rim – The jet holes under your toilet rim can also be clogged with residues or sediments that accumulate over time because of repeated flushing. This causes weak water pressure that comes out of the holes.As time goes by, more and more mineral deposits will accumulate under your toilet rim if this issue will not be resolved. So, chances are, water pressure will worsen and become weaker, thus leading to slow flush. 
  • Clogged drains – Clogged drains can be the cause of your toilet not flushing completely. You might want to consider that you have some blockage through your drain or waste lines especially if you have kids. This can be a serious problem if not addressed promptly. 

Items such as toys, wipes, sanitary napkins, floss, and other materials that are small enough to fit in and can clog your toilet drains. If not resolved immediately, the item that is causing the blockage can go only deeper down the waste line and it will only make matters worse.

  • Damaged toilet bowl – The system inside a toilet bowl operates through pressure. The colon has to be really airtight for it to be able to pump water out of the drain pipe. If the interior colon is somehow damaged or cracked, then there won’t be enough pressure and will only lead to weak flushing. 

This needs immediate action since the interior colon of the flushing system is a little too intricate and must be fixed only by the pros. This probably is not really advisable for people who like doing DIY tasks because it might only cause you bigger problems if you make a mistake.

  • Weak flushing system – The flushing system in your toilet tank wears down over time. Possible moss build-up may happen due to sediments and mineral deposits that come from hard water. This can be the main cause of faulty flushing system since it will reduce the diameter of the pipes which can reduce water flow through the pathways. 
  • Old/defective flapper – The flapper valve is one of the significant part of the flushing system in your toilet tank. It is supposed to open up when toilet is flushed to completely drain out the water and close down when water is emptied in the tank.

However, if the flapper valve does not open completely, this will result into slow flushing.  It may be because of the chain or rubber string that is attached on the plunger connecting the flapper.

This can be loose because of wear and tear or maybe it is too long that it does not pull the flapper enough to make an adequate opening for the water to completely drain. Thus, you’ll have a toilet that flushes slowly and incompletely.

toilet low flush

4 Significant Tips to Proper Toilet Maintenance and Care 

  • Refrain from disposing garbage – Strictly avoid throwing away garbage in your toilet such as wipes, sanitary napkins, toilet paper, dental floss etc. You may think that when you flush these items away, it also goes down the septic tank… Well, think again.

Some of these items can block the waste pipelines since the pipe circumference decreases overtime due to scum build up around it. Chances are, materials thrown into the toilet get caught up into the pipelines when flushed down. This will result into clogged drains which will eventually lead to water back up or an overflowing toilet. 

  • Immediately fix minor problems – You must not take things lightly and neglect simple problems that may occur. Every minor issue in your toilet requires immediate attention to avoid escalation. This will also save you from spending too much and will save you from stress.

For example, if you have water running in the toilet bowl , immediately check the flapper if it is totally sealed when closed. You can use some dye or food coloring. Put a few drops in the toilet tank. Wait for a few minutes and if you see the color coming out of water in your bowl, it means the flapper is already defective and it needs replacing. 

  • Avoid using harmful chemicals – When cleaning your toilet bowl and tank., avoid using harmful chemicals that may cause corrosion. This might result into interfering with the water pressure when flushing or when filling the tank. 

You can use light toilet cleaning chemicals or better yet use the most natural way, baking soda and vinegar. Sprinkle one cup of baking soda into the toilet and then pour one cup of household vinegar into the bowl. Let it stay for 30 minutes and then scrub with a toilet brush. 

  • Conduct regular inspections – It will definitely make things easier for you if you make a regular inspection of your toilet. Checking and repairing minor things such as small leaks or blockages will ensure that your toilet will always function well. Whether you DIY the maintenance or you hire one of our Boston plumbing technicians to do the inspection, the objective is for you to avoid spending more in the long run.

Repair Toilet Flush in Boston

7 Important Signs To Watch Out For If You Need to Repair Your Toilet

Toilet Plumbing Problems in BostonPerhaps the most important plumbing fixture or equipment in home is your toilet. It’s one thing we CANNOT live without.  

Toilets have made our modern life so much easier. Imagine if we didn’t have any toilets in this new age, will we ever realize the importance of it?  We would never experience the convenience it gives us now.

Fortunately, most of us were exposed into the culture of having and using toilets to dispose of our wastes properly but what if your toilet malfunctions? What if you have a slow draining toilet? How will you know?  Here are the tell-tale signs:

  • Clogs more often – If you know how to take good care of your toilet, you’ll only experience occasional blockage or you may never experience any blockage at all. On the other hand, if you find that your toilet clogs more than once a week, then you must have a more serious problem.

You must have a defective flushing system or there might be a blockage somewhere in your waste pipeline. The parts in the flushing system will eventually be worn out overtime but either way, you still need to address these problems.

Either you hire a professional plumbing contractor to repair the damage in your flushing system or have him dislodge the blockage.

  • Your toilet has a weak flush – If your toilet only swirls when you flush and the water does not even go down, then there must be something wrong with the flushing mechanism. You need a valve replacement and you need to get the right fit.

If you know DIY toilet repairs and you have experienced this kind of issue before and were able to resolve it, then it’s okay for you to do the replacing of the valve. Otherwise, let our techs do the work for you.

  • Tank does not refill with water – After flushing, if the tank or toilet does not refill with water, most probably the fill valve is defective already and you might need to replace it. In this case, you must be sure to get the correct size to be able to install the valve correctly.

Also, you might want to consider checking the flapper if it closes properly after flushing the toilet. If you hear water running after flushing and it won’t stop, most probably the flapper isn’t sealed so there is water going down the drain. We suggest that you replace the flapper to ensure that every after flush it will shut close and it won’t allow any water to find its way down the drain.

  • Standing water around toilet base – Standing water indicates that you have a toilet leak. It could probably be around the seal. This needs to have a seal replacement in order to stop the leak.

Call us to fix the problem. This is to ensure that re-sealing it will be done correctly because if there are parts that will be left unsealed, then the problem might get worse and you wouldn’t want to be spending more for a job that was supposed to be done only once.

  • Water leaking out of toilet cracks – Water leaks don’t always come from the seal around the toilet base. Sometimes it can come from the cracks of the porcelain around the tank or the bowl.

Clean your toilet bowl or toilet tank outside and check if there are any stains or deposit build up around the porcelain or if you see any parts in the surface that is moist. If so, your toilet of tank definitely has cracks and water is leaking out.

Depending on the severity of the leak, if there are chunks porcelain that were detached, then we would recommend that you replace your toilet with a brand new one.

  • Toilet runs constantly – In most cases, the problem comes from the flapper when it is not sealed properly after flushing. Just replace the flapper with a new one then usually it will solve the problem.

However, the problem may also come from the float. If the float does not stop the water from filling, meaning if it fails to shut off the fill valve the waterwill overflow and will continue running.

The solution may be just adjusting the rod that connects the float to the fill valve and slightly bend it downwards so that it shuts off the valve when water rises enough. If the problem still continues, then maybe you should call our Boston MA plumbers to address the issue.

  • Corrosion on metal parts – If your toilet is showing signs of rust and corrosion it’s metal parts then it means that your toilet has worn out. Wear and tear may only show on certain parts so, all you need to do is only to replace those old components with new ones.

However, if you see widespread rust and corrosion then we recommend that you replace your entire toilet to save you from escalated problems in the future. 

Slow Flushing Toilet in Boston

5 Effective Slow Flushing Toilet Fix Tips

Boston Toilet Long FlushToilets have absolutely significant roles in every household. This may be the one thing you may never live without. Toilets are the main lavatory equipment that properly disposes off wastes. On the other hand, this can also be the source of every house owner’s head ache.

When your toilet becomes defective overtime due to wear and tear and you tend to delay inspections and repairs… Chances are, you’ll have bigger and more complicated problems with your toilet.

You may have recurring problems and this will potentially drill a hole in your pocket. So, we strongly urge you to have a regular inspection and never ignore first signs of toilet problems. Bear in mind that there are toilet issues that are intricate and only professional plumbers can solve.

However, we have list down below some important DIY solutions to help you address your toilet’s issues immediately to avoid bigger problems in the future and more importantly to avoid spending more. So, read on and enjoy!

  • Sufficient water in tank – The problem may be because you simply need to adjust the float higher than usual in the toilet tank so the level of the water will increase as well. You may need to bend the rod attached to the float upwards just a little bit, allowing the water to go higher than the usual.

However, be extra careful when adjusting the float rod or bending it as this is attached to the fill valve. The fill valve is where the water comes out to fill the toilet tank. Chances are, you might have a bigger problem if you damage the fill valve because the water will continuously flow and won’t shut off.

  • Working flapper – The flapper is the one responsible for draining your toilet tank. It needs to have enough opening space once you flush the toilet in order to drain the water.

If there is not enough space or if the flapper does not really open enough the water that will drain into the toilet bowl will be inadequate. You need to simply check the chain or rubber that is connecting the flapper and the toilet plunger. You need to make sure that it has the right length to provide enough opening space for the water to drain when the flapper lifts.

  • Trap must be clear – A toilet can be clogged when there is an obstruction through the trap or the vent pipeline which are easy to check.

Ensure that your trap clear of any obstructions. Overtime, if you or you allow people in your household to dispose of materials that are non-biodegradable or items such as toys, wipes, sanitary napkins, floss, and other materials – That can definitely block your drains.

The first thing that you should do is fill a pail one to two gallons of water, then pour everything into the toilet. If your toilet only swirls but does not flush then the blockage is still there. Try using a plunger to suck up the blockage or probably use a snake if it still does not work — That is how to unclog a toilet fast!

  • No obstruction in vent pipe – This is the one that protrudes from the roof of your house by about 30 cm or a foot. This measures about five to eight centimeters or two to three inches in diameter. This is located on top of where your toilet is placed.

Just run a plumber’s snake through the pipe and you can also pour water in it with an extended nozzle or you can also use water pressure in order to flush out the blockage.

  • No blockage around rim – You may locate calcium or other mineral build up under the toilet’s rim after sometime which may be the cause of slow flushing since water from the tank is obstructed by the blockage even if it has enough pressure.

If this is the case, you can use a toilet cleaner that can help dissolve mineral build up. Just follow these simple steps.

  1. Turn of the supply of water
  2. Drain your toilet tank
  3. Open and hold the flapper
  4. Pour ¼ liter of your toilet into the flush valve
  5. Let is stay for 60 minutes
  6. Quickly seal the flapper
  7. Turn on water supply
  8. Flush your toilet 2-3 times to wash down cleaner
  9. You can do it again when needed

Choose a Reliable Plumbing Company in Boston That Can Fix Your Slow Flushing Toilet

So, just remember these helpful tips and chances are you’ll never go wrong. Bear in mind that the faster you act, the lesser chance of you to have bigger toilet problems and it will not only save you from spending too much but it will absolutely save you from a lot of stress. Proper maintenance is the key to having a good plumbing system in your household.

For more intricate low toilet flush problems, we recommend that you leave it to the experts. Trust only a reliable plumbing company that’s been serving people for years now.

We are Plumbers 911 and our plumbers have over 10,000 hours of training and they are all licensed. Backed by years of experience, with high-end tools and top of the line equipment, all our plumbing experts are bonded and insured.

Remember, for toilet leaks, slow flushing toilets or any plumbing issues that you think is impossible to be solved, call Plumbers 911 Boston now and schedule a thorough plumbing check-up. It is definitely cheaper than getting hit with a huge repair bill. 

We’ll flush all your plumbing worries down the drain!

Watch this video to know more about Plumbers 911 and our emergency plumbing service!

Posted on: February 26, 2019

Six Frequent Toilet Plumbing Problems Experienced by Independence MO Residents

Worry-free Toilet Repair from Your Independence Plumber

toilet repair Independence MOIn your Missouri home, there are some things that just have to work reliably. You need your oven for cooking, the smoke alarm for safety, and without the lights, you may as well go to bed when the sun goes down.

However, of all the fixtures in a home, there is one that MUST work reliably every time: the toilet. Unfortunately, there are quite a few things that can go wrong with a toilet.

The toilet is a durable plumbing fixture that may last for years or decades even. However, we all know that toilet problems are the most terrible plumbing issues for homeowners. Even the bravest of men dread the very thought of unclogging the throne — err the toilet.

But then again, that’s only one plumbing problem amongst the many that you’d have to deal with. There’s still a lot more that you need to watch out for and that is why knowledge, familiarity and basic plumbing skills are important. Check out these tips that will come in handy during toilet repairs.

In this article, we will be covering:

  • Clearing a clogged toilet 
  • Troubleshooting toilet issues like ghost flushing, weak flushing, toilet leaks, etc
  • How to repair a leaking toile
  • Toilet repair noise and what to do when your toilet makes noise when flushing
  • Weird toilet flushing sounds – what do they mean?
  • How to repair a toilet flange
  • How to replace your toilet flange

Clogged Toilet Fix

Licensed Plumber for Clogged Toilets in IndependenceIt seems like clogged toilets are the most unbearable of all plumbing emergencies we can ever encounter at home. Though such problems provide lesser inconvenience as that of a burst pipe or a leaky hot water heater, they are, on the other hand, messy and gross to handle.

Who would ever want to deal with the toilet, eh? Luckily for us, if it’s not that hard to unclog the john.  Do you know how to unclog a toilet the natural way,without the use of chemical cleaners?

Clearing a Clogged Toilet

  • Boiling Hot Water
    For minor clogs, the use of boiling hot water generally solves the problem. Just pour a bucket of water into the toilet, making sure that the motion is speedy and yet not so fast for the john to overflow. If a bucket doesn’t get rid of the issue, try another gallon or two.
  • Baking Soda And Vinegar
    If boiling water doesn’t turn out as your bathroom superhero, get your good old baking soda and vinegar out of the kitchen cupboard! It’s time to do some cooking — errr unclogging — using these common ingredients that we’re pretty sure you always have at home.Now pour a cup of baking soda into the toilet. Follow it up with a cup of vinegar. When the two ingredients combine, they will create a fizzing reaction. Once done, check if the toilet is back to working condition again. If not, let’s try another method!
  • Boiling Water And Detergent
    Try using your favorite dish detergent to remove the clog. Just pour a cup of it into the toilet to lubricate the drainpipes. Once your water has boiled, pour the entire kettle into the john. Now double check the result. Still clogged? Move on to the next one below.
  • The Plunger
    If lubricating the drainpipes still isn’t enough, go get your handy dandy plunger. Position it right into the toilet’s drain hole. Plunge in a steady, consistent yet fast pace. You may also plunge as you flush your toilet to give it more draining action. Repeat the process for about 15 times and check if the problem is taken care of.
  • The Snake
    If your ceramic throne is still not functioning well, you’ll have to get down and dirty. Wear rubber gloves to keep your hands clean. Get your snake or auger, insert it into the toilet drain and move the crank clockwise until the tool touches onto something.When it does, keep on pushing the cable further to break the clog into smaller pieces. You’ll know you’re done snaking around when the wire already moves freely inside the drain. Slowly pull it out and dispose of any waste material inside a bucket or a similar container.

Six Frequent Toilet Plumbing Problems

Troubleshooting Toilet Issues

Ghost Flushing
This isn’t a rare toilet problem. Many homeowners experience phantom flushing which involves the presence of sound similar to when a toilet is flushed. What’s inconvenient about this is that the fixture will intermittently make that flushing sound even when no one’s using it.

What causes the problem could be a damaged flapper or a bad flapper seat. The malfunction results to a leak between the tank and the bowl, therefore making water leak and causing the strange reverberation which can strike anytime.

To fix this plumbing problem, the flapper seat must be cleaned or replaced when it’s already too worn out to work.

toilet problems and repairs Independence MOWeak Flushing
Weak flushing is another problem that you have to be ready for. There are times when you’ll notice that waste materials take a long time to get flushed — even when you only peed.

Such a problem may be caused by clogged jet holes. Just get a coat-hanger and poke through those holes to get rid of the sediments and mineral deposits that have accumulated in there. Be extra careful so you won’t scratch the bowl.

Toilet Leaks When Flushed
If you ever hear water trickling into the toilet tank, there’s probably a problem with the supply lines, the float, the refill tube, the ballcock or the inlet valve. This issue is caused by a leak somewhere in the assembly or a component that should be adjusted.

To fix the leak, make sure that the float will stick and that the refill tube isn’t installed too far into the overflow tube. Remember that the refill tube should only go as far as a quarter of an inch below the overflow tube.

Make the necessary adjustments and if these parts won’t get fixed, the only solution left is to replace them.

fixing the toilet Independence MOLeaking Seals
If it leaks somewhere at the base or between the tank and the bowl, you’ll have to check the seals. A leak between the tank and the bowl will result to water shooting from this area.

A leak at the base will cause a forever wet bathroom floor and sooner or later, a wobbly toilet. Tighten the seals and if they’re already worn out, replace them.

Clogs and Toilet Overflowing
Clogs are the most common toilet problems experienced by property owners. It appears that the more the toilets are used and exposed to different waste substances, the more they get clogged.

Always have a cup plunger ready in case blockages occur. If the plunger won’t do the trick, rely on a plumbing snake. These two are the most efficient plumbing tools that you can use to eradicate stubborn clogs. 

clogged toilet repair IndependenceHow to Repair a Leaking Toilet

Throughout the years of use, you’ll eventually discover that your toilet is leaking. Don’t panic. It has parts that deteriorate as the fixture ages so a simple repair or replacement will solve the problem.

But before you perform the necessary repair, it is important that you identify the source of the issue accurately. From there, you should be able to discern the best way to stop the water seepage.

To help you diagnose your toilet, here’s a quick and easy-to-understand guide we’ve written just for you! Check out the most common causes of toilet leaks.

  • Worn-out bolts and washers create leaks. There are two large bolts that secure the tank to the toilet bowl. Water will flow out of the connection if these components deteriorate or get worn out.
  • There’s also a gasket that’s installed between the tank and the toilet bowl. This measures three inches and is responsible for creating a seal between the two toilet parts. If the gasket corrodes, the tank will leak because there will be nothing to support the nuts, bolts and washers in this part.
  • The toilet tank is a container that holds the water used for flushing. Sometimes, objects fall to the tank that cause cracks. If these are not repaired immediately, they will only get bigger and result to leaks.
  • The tank has a float assembly inside. It is a set of components that give the fixture its flushing feature. However, when the assembly gets damaged or malfunctions, the flow of water out of the toilet tank will be continuous. Thus, the tank will overflow and cause leaks.
  • Another culprit is a loose water supply pipe. If this supply pipe becomes loose, cracks or breaks, leaks will surely develop.
  • Speaking of tubes, there’s an overflow tube inside the tank. This component is responsible for letting water out of the tank to prevent overflow. So when this tube gets clogged, you should expect the tank to get totally filled up and water to flow out of the container non-stop.
  • Aside from getting loose or breaking, the supply pipe may also get corroded. When they do, water will flow out continuously.
  • Like the tank, the toilet bowl is also vulnerable to cracking. Once you notice that your toilet bowl is already damaged, it must be replaced immediately not only to avoid leaks but also to prevent accidents.
  • Another essential component of the toilet is the fill valve. When it fails to work as efficiently as it should, the tank won’t be watertight anymore. That said, have this part replaced immediately when it’s already broken.
  • When the leak comes from the base of the toilet, it must be due to a damaged or worn out toilet flange. As usual, this part must be replaced with a new one that will keep the connection tight and leak-free.

Toilet Repair Noise: What To Do When Your Toilet Makes Noise After Flushing

Independence MO toilet flush repairAside from getting clogged, we’re pretty sure that you don’t want your toilets to make weird sounds that might scare the hell out of you in the middle of the night. The only problem is, these sounds cannot be avoided especially when you have an old toilet bowl.

Just like other plumbing fixtures, your toilets have parts that wear out and get damaged over time. And when they do, weird sounds reverberate from them.

Now there are several types of sounds that you might encounter but if it’s specifically making a loud reverberation, much like a foghorn, such a problem may result from the ballcock assembly’s loose washer or a ballcock that isn’t perfectly sealed.

Check out this easy DIY Guide:

  • Remove the toilet tank’s cover and flush the bowl. If you discover that the valve makes the noise, try to resolve the issue by lifting the float ball up. If doing so gets rid of the noise, it just confirms that there’s a loose or damaged washer in the ballcock assembly
  • To fix this problem, first shut off the water supply and flush the tank.
  • When you’re done, locate three screws that are supposedly situated right on top of the fill valve. You’ll have to disassemble the valve assembly so start by removing the screws using your screwdriver. Lift the ball and armature. Finally, carefully lift the flush valve and get it out of the tank.
  • Remove the washer that you’ll finally access at the bottom of the flush valve. Replace it with a new washer. Put the assembly back in place and turn the water supply on again. Test if the sound has been removed. Otherwise, proceed with the next step.
  • Check the valve and make sure that it is sealed. If it’s not, you’ll need to replace it as well. Turn the water supply off again before doing the repair.
  • Flush the tank and scoop out any excess water. You may also use a sponge to absorb the water at the bottom of the tank.
  • After this, proceed by detaching the water supply line from the toilet’s valve connector which is found right under the tank. Loosen the locknut of the toilet valve with the use of your pliers. Remove the nut screw and lift the worn out valve out of the tank.
  • Place a new valve and adjust the water fill level. Screw the toilet valve’s locknut again and tighten it with your pliers.
  • Finally, reconnect the water supply line to the toilet’s valve connector. Turn the water supply on and let the tank fill. Make sure that the water level is an inch above the overflow tube. Flush the toilet again and check if the problem has been fixed.

Repair Toilet Flush: What’s That Weird Sound?

Here are some troubleshooting tips when identifying toilet problems based on flush sounds:

  • Phantom flushing means that the toilet is creating a flushing sound even when there’s no one using it. This can be due to water waste that’s brought about by a leak somewhere. Find the leak and fix it.
  • Weird sound after flushing that usually lasts more than a minute may indicate a pressure issue or restricted water flow. Try adjusting your pressure valve. If it doesn’t get rid of the noise, open the tank and lift the float. Then, if the issue is resolved, try replacing the float.
  • A “cchhhhh” toilet flush sound that occurs sporadically can be a sign of a flapper problem. If the flapper is worn out, an outflow ensues and the toilet tries its best to stabilize the water level, thus creating this sound. Replace the flapper.
  • If it is having gurgling sounds while it’s refilling, there’s a big chance of the water flow not becoming uneven. Adjust the valve to reduce the supply of water to the tank.

how to replace a toilet flangeHow to Repair a Toilet Flange

Is your toilet squeaky or wobbly? Maybe you need to replace the flange! Over years of use, it is just normal for the toilet flange to deteriorate or get a bit unfastened since it’s always exposed to water.

However, it’s not the easiest plumbing project especially if you’re not a skilled plumber. But as they say, great skills develop from experience. Before you get your plumbing kit and dive into the project right then and there, familiarize yourself first with the flange and its function in your toilet

The flange is necessary as it connects and secures the toilet to the drainpipe in the floor. Without it, your toilet will not stay secured in its place and water or even waste will seep out.

Now when that happens, you should prepare yourself for major cleaning! That being said, you should attend to the problem right away once your toilet bowl gets wobbly. So how do you fix or repair a broken flange? Read this step-by-step guide to learn how!

Your toilet flange has a metal or plastic ring holding the toilet to the floor.  It is important because it secures the toilet bowl to the floor and makes the connection to the drain pipe leak-free. You’ll notice that there are holes at the sides of the flange. These holes are where the bolts go through in order to keep the toilet bowl steady.

When this breaks, your toilet can’t be used.  You might also discover that the bowl is a little bit wobbly.   If you encounter a rocking toilet, well, that means your flange is no longer holding it.

There will come a time that you’ll see water pooling at the base of your ceramic throne. These signs indicate that the toilet flange is already worn out.

Replacing it isn’t as easy as you think.  You can purchase repair plates that fix some breaks within the ring or repair rings to cover the entire flange.

Here’s How You Can Replace Your Toilet Flange

  1. Turn the water supply valve of the toilet off to prevent filling up the tank. Now empty the tank by flushing the toilet. You can use a sponge or scoop the remaining water out of the tank. Just ensure that it’s completely empty.
  2. Unscrew the nuts and then loosen the bolts that secure the toilet bowl to the floor. Afterward, break the wax seal that connect the fixture to the flange. When you’re done removing the wax seal, you should be able to remove the bowl. Set it carefully aside and make sure that you’ll put it on top of a towel or rags to prevent it from falling sideways or breaking.
  3. Clean the area where the new flange will be installed. The old wax should be removed with the use of a putty knife or any similar substitute. Guarantee that the area is completely clean to make the new connection leak-free.
  4. If the old toilet flange is not broken or cracked, you can still use it. Otherwise, you’ll have to replace it. If it’s not broken, the leak may be due to loose bolts and nuts. Tighten these parts and re-install the fixture. Check for leaks.
  5. If the flange is damaged, you can get a spanner flange first. It’s a semi-circle part of the flange that can be replaced. You should just unscrew it, remove the bolts and install the replacement in place. Drill the spanner flange to the floor to secure the connection.
  6. Now if the damage is severe and the entire flange is broken, you can just replace the old flange. Clean the installation area; pour the concrete in and let tit set. Put the new flange on top of the concrete and screw it in place.
  7. Put the wax gasket down on the flange. Guarantee that it’s aligned with the flange and the toilet to make the connection leak-free.
  8. Reinstall the toilet bowl and tighten the bolts. Connect the supply line to the tank and turn the water supply valve on. Refill the tank and flush the bowl. Check for leaks.

 Call Plumbers 911 Today

From toilet tank installation to any kind of fixture or toilet problems, give us a call today! We have the most reliable Independence plumbers in the Missouri area. We are available 24 hours a day, 7 days a week! Call us today for immediate assistance!

Posted on: December 30, 2018

Stop Wasting Water This Year and Do These Top 3 Plumbing Upgrades

The start of the year is always a perfect time to assess your home’s current plumbing system and think about upgrades.  For one, you can replace your current plumbing fixtures to ones that can help you save money in terms of water expenses.

All you have to do is find a local plumber in Chicago who can efficiently deliver this task (that’s what we’re here for!)

Consider these upgrades if you want to save water this year

Water Saving Shower Heads

ultra low flow shower headDid you know that showering accounts for almost 17% of an American home’s total water consumption?

A typical shower can dispense as much as 2.5 gallons of water per minute, and that’s a lot! Licensed plumbers in Chicago can attest to this. Replacing shower heads is the easiest solution.

Luckily, there are lots of ultra-low flowing shower heads available in home improvement store and plumbing supply shops.  Once you find a local plumber in Chicago, you can mention about this and ask for his suggested best brands.

Low Flow Faucet Aerator for the Kitchen and Bathroom

low flow faucet aeratorLow flowing bathroom and kitchen faucets have aerators that work to lessen the flow of water while keeping the water pressure constant. Be concerned if your kitchen or bathroom faucet dispenses more than two gallons of water per minute. Ideally, it should only be 1.5 gallons per minutes. If budget is your concern because of the number of faucets to be replaced in your home, you can opt to replace two faucets first and then go on with the rest in the coming months. Or, find plumbing services in Chicago that offer promos or discounted offers for projects like this one.

This could also be a cause of concern for commercial establishments. Just imagine the number of low flow faucet aerators they will need! Then again, the key here is to find local contractors in Chicago that will charge affordably.

Dual-Flush Toilets

dual flush toilet buttonMore and more bathrooms are being replaced with dual-flush toilets that only use up to 1.28 gallons of water per flush. These toilets have two buttons for flushing – one for flushing liquid wastes and the other for flushing solid wastes. This way, you will only flush water that you need.

The dual-flush toilet is revolutionary and highly-effective in saving water. In fact, new buildings in Australia, New Zealand, Singapore, and Israel are required to install dual-flush toilets. You must remember though that it is more expensive than the regular toiles. Then again, think about the amount of money and water you will save in the long run.

Let Us Help You Find a Local Plumber in Chicago

Plumbers 911 is a reliable plumbing company in Chicago that has a wide list of licensed plumbers. You do not need to go far to find a local plumber in Chicago. All you have to do is call us and we can dispatch a 24-hour plumber in IL to your home in less than an hour.

 

Schedule a visit today by calling (877) 445-6127. But before you go, make sure that you check out our coupon page to get $50 off on your initial service call!  

Plumbers 911` Chicago discount coupon

Posted on: January 15, 2018

What You Need To Know About Basement Toilet Installation in Chicago

basement toilet installation in ChicagoYou’re making a worthwhile decision if you are considering remodeling your basement and doing a basement toilet installation in Chicago. Homes with basement bathrooms sell higher so homeowners are able to profit as much as eighty-five percent of their initial investment. Indeed, you can make it convenient for each household member when there’s a bathroom in the basement.

 

Why Build a Bathroom in the Basement

Old homes are usually built with only one bathroom. This could be a problem when you have guests coming over. Especially so when your guests are staying in your basement guest room. Are you the kind of host that would want his guest to be inconvenienced by not having a bathroom in the basement?

A Basement Toilet Installation in Chicago is a Special Project

Building a bathroom above ground is not the same as building a basement bathroom. There are additional concerns when you build a toilet in the basement. For one, there’s the concern for ventilation and lighting. There is a greater possibility of moisture in the basement than any other parts of your home.  

A basement bathroom also requires a special plumbing set-up. In the basement, a toilet will not flush successfully if not installed properly. Same thing for the sinks, tubs, and showers in the basement bathroom. This is because the sewer lines will then be higher than your basement bathroom.

A basement bathroom should have a sewage ejector installed to resolve this dilemma. To do this, a part of the basement floor will have to be excavated to save a space for the ejector.  Wastewater and solid wastes will directly go to this sewage ejector. A plumbing professional can install a sewage ejector for you. Installation is pretty complicated and should only be handled by the pros.

There is still one option, but this will be more costly. A macerating unit will be perfect for a basement bathroom. Sink and tube wastewater can also be handled if you will be able to choose the right size. A macerating unit requires no digging, unlike the sewage ejector. You will just need additional space for the pump box and the macerating unit and place this behind the toilet or in the bathroom wall. A macerating unit requires no maintenance so you’ll still be able to save money in the long run. The only cost you’ll worry about is its installation.

Your Basement Bathroom is Possible

As with any other construction project, you will need to have a plan ironed out. Also pay attention to your budget. Meanwhile, let a licensed Chicago plumber handle your basement’s pre-existing piping and wiring set-ups. Plumbers 911 Chicago can help you find a reliable local plumber who can make this dream project come true for you. Call (855) 484-3911 to ask for a free quote and to schedule an appointment. You’re on your way to add value to your home!

 

Posted on: August 8, 2017

Toilet installation in Beaumont – Reasons to Leave it to the Pros

plumber for toilet installation in BeaumontAre you thinking of replacing or upgrading your current toilet? Or do you have a newly constructed bathroom or powder room in the house? Toilet installation may look like an easy task, but it is not. If you do your research, you will see how complicated some steps are. Moreover, there are many considerations to think about before installing a new toilet. And if you’re not really the DIY type of homeowner, expect some hits and misses to occur. This is why it is highly recommended to leave your toilet installation in Beaumont to the pros.

 

Points to Consider for Toilet Installation in Beaumont

  1. Specifications – You will have to measure the area where the toilet will be installed. Typically, it is from the wall to the center of the outlet. Standard toilets have a size of 12″, but since toilet bowls also come in 10″ and 14″ sizes, you must do the measuring to be sure.
  2. Toilet footprint – For toilet reinstallation for remodeled bathrooms, you will have to refer to a toilet footprint specification sheet for the area where the toilet will sit.  For new installations, the flooring should be close enough to the ring on the toilet flange.
  3. Toilet height – The “comfort height” for users of the toilet being installed should also be considered. For example, taller and older people would need toilets installed a bit higher so there will be no need to bend lower every time.
  4. Elongated or round front – Elongated fronts are best for younger users. However, you should consider a toilet with a round front if your toilet area is small. 

A licensed Beaumont plumber would be able to know what’s best for you based on these points for consideration. You will have the luxury of rest and peace of mind if you let the pros install your toilet for you.

Hire a Licensed Beaumont Plumber for the Job

Having a licensed Beaumont plumber doing the job for you may actually work well to your advantage. Without the right tools and experience, you could end up doing more harm than good to your bathroom. Yes, installing the unit looks easy but having it installed properly is a different story. Will it leak? Will it break? Did you tap into the correct pipes? You have to wait to find out. Professional plumbers get the job right the first time.  Lastly, you will definitely need a professional plumber to install a toilet in the basement because it has to include a pump.

To be honest, finding a reliable professional plumber is easier than installing a new toilet. You can ask family and friends for recommendations. Word of mouth advertising is reliable because it comes from the first-hand experience. You can also call plumbing companies in your locality to ask for free quotations. After making a number of calls, you can decide which gives the best deal.

Choose Plumbers 911 Texas for Your Toilet Installation in Beaumont

Plumbers 911 has the largest network of professional local plumbers nationwide. By referring you to a licensed plumber in your area, you are assured that you will be serviced in as quick as an hour. Call Plumbers 911 Texas at (409) 237-3137 to ask for a free quote and to schedule a visit.

 

Posted on: July 30, 2017