Category: Sump Pump Repair

Sump Pump Repair and Maintenance Guide for Chicago Homeowners

what is a sump pumpWhat is a Sump Pump For?

A sump pump, based on its name, is basically a pump that is used or put in a sump. A sump is a hole like the ones that you can find in your basement which has a typical lid over it. The sump pump sits at the bottom of that pit.

Sump pumps are installed in specially lined pits (called “sumps”), designed for drainage. In automatic sump pumps, when enough water accumulates in the pit, a sensor is activated which turns the pump on. The system is then able to drain the water, via a drainage pipe that deposits the water safely outside your home.

In This Article, We Will Be Covering:

  • Why you need a sump pump
  • How does a sump pump system work
  • Types of sump pumps
  • Which kind is right for you
  • When is the best time for an installation
  • Sump pump problems and failure
  • Sump pump maintenance guide and tips
  • How to keep your sump pump well maintained
  • How to use a sump pump
  • Common repair problems
  • Sump pump not working?  This might be why..

Why Do You Need a Sump Pump?

working sump pump could prevent your basement from being flooded and walls wet during the rainy season. It plays a major role in keeping your basement dry, therefore saving you from expensive repairs.

If your sump pump is broken and neglected, you open your home to a serious risk. Understanding the purpose of your sump pump will quickly open your eyes to its important function and the need to have it repaired as quickly and professionally as possible. 

How Does a Sump Pump System Work?

sump pump repair Chicago ILThis handy device is basically a pump that is submerged bottom of what is known called a sump pit.

This pit and pump are installed at the point most likely to flood in your crawl space or basement. Then, the water that surrounds the foundation of your house is directed into a perimeter drain system.

A float is usually on that pump. It works similarly with a toilet tank’s float where you pull the top of it. The sump pump works by having the water rise to a certain level until a switch is hit or activated. This kicks on the sump pump and it draws the water coming from the bottom of the pump. It is then pushed up by a check valve towards a series of pipes until it reaches an area outside of your home.

The pump will activate when water reaches a certain level inside the pump itself. Once activated, the pump will divert the water into the nearest storm drain, dry well, or other location set up for the purpose.

If your house lacks this system and you are at risk of flooding, call our expert Chicago plumbers.  Your sump pump system is often installed at the base of your foundation. Any water that makes it into the drainpipes and quickly removed by your sump pump.

Types of Sump Pumps

There are many types of sump pumps available. There are those that are hard-wired right into your house’s electrical system, and there are those that are powered by plugging right into an outlet. Many pumps also come with a battery backup to continue working through power outages and storms- when it is needed the most.

There are two main kinds of sump pumps. Our technicians can help you select the kind that is right for your home.

  • A Pedestal or Column-Type 

Pedestal-type pumps are mounted above the sump. They are the less expensive option of the two kinds of pumps, and last a long time – up to 30 years. This makes them an attractive option for the budget-conscious homeowner. However, they are more obtrusive and can be louder than submersible pumps.

  • Submersible-Type 

Submersible-type pumps are mounted directly inside the sump, so they are less obvious, which might make them a preferred option for some homeowners. They are more expensive than pedestal-type pumps and have a shorter lifespan of 5 to 15 years. However, they are quieter, and handle debris better than pedestal-type pumps.

There are other variables that you can use to determine which sump pump is right for your home. 

Which Kind is Right for You?

  • Do you need an automatic or manual pump? The automatic kind can detect when water needs to be removed, so you won’t have to monitor the level yourself.
  • How much horsepower does your pump require?
  • What is the voltage?

When is the Best Time for a Sump Pump Installation?

The best time to do sump pump installations is during early spring when there is less heavy rain. If your neighborhood is experiencing a huge water influx, call us immediately.

Other sump pump services include:

  • Ensuring that the flow of heavy water influx are set properly
  • Ensuring that the check valves are operating properly
  • Ensuring that the electrical connections are tight if you have a stocked check valve which pump is not operating properly
  • Making sure that the sump pump is ready to go, especially when there is heavy rain and water

Sump Pump Problems and Failure

sump pump repair service ChicagoIf not taken into action immediately, sump pump failure may have a few consequences. The cost can be very expensive for repairs, especially if the basement it’s on is already finished.

Once your sump pump breaks, the water will be infiltrating the basement and flood the entire area. This is huge property damage and most of the time, property insurance does not cover these damages.

You need to ensure first and foremost that your sump pump is properly installed. It would be great if you have a check valve put into it so pump will not set off in just short cycles.  To avoid further damage, you must maintain this once in a while and perform immediate repairs. Proper installation is also a must because, admit it, you wouldn’t want to suffer from having problems in the middle of its lifetime, right?

Sump Pump Maintenance Guide and Tips

If your pump is not properly working your basement can quickly suffer water damage. Many people don’t check on their pump until it is too late and their finished basements have suffered thousands of dollars in damage.

Because it is out of sight and out of mind, many forget to have it serviced and repaired. A quick call to our local Chicago plumbing expets will insure that this doesn’t happen to you. 

Easily Test your Pump In a Matter of Minutes

You can easily test your sump pump by removing the cover and filling the pit completely with water. This should rise the float switch and activate the pump rather quickly. The pump should then pump the water out and automatically switch off.

Cleaning and Repairing Take a Professional Touch

While testing your pump to see if it is working properly is easy, cleaning and repairing take skill. Often dirt, gravel, sand, and other debris can make it inside your pump and drastically reduce its efficiency and lifespan.  Our certified Chicago techicians know exactly where to look and can clear the discharge line opening of any blockage, allowing the water to exit the home smoothly.

Always Have a Backup Plan

Backup power is vital for when the power goes out it is usually storming outside. Storms bring water, and water spells trouble for your basement without a working sump pump.

Usually, your sump pump will draw AC power from a wall outlet or your home’s electrical wiring and supply the power to your sump pump. In the event of power outage, a backup will kick in and take over supplying power to the sump pump. As such, you need a reliable system that will automatically send power from your backup to the pump.

Your pump may also fail if there is mechanical failure or excessive use. Whether your motor overheated or your power went out, a battery backup can give you additional hours of protection against water damage.

The handy mechanical device that you rarely think about does vital job in keeping your basement dry and free of flooding. Now that its broken, your home is at risk for frequent flooding and water damage.

Take the time to check your sump pump today. A specialist can help extend the life of your pump by cleaning the parts, pit, installing backup power, and ensuring everything is working to its full capacity.

How to Keep Your Sump Pump Well Maintained

Sump pump not working ChicagoYour sump pump is tested not during the summer but during rainy days, and it is only by then that you notice that it has malfunctioned.

During these days, the quick flow of rainwater contributes to the ground water making the water table rise quickly. The sump pump kicks on as the ground water level reaches the float activation point. It keeps the water level below the basement and therefore lessening the pressure below the basement floor.

A lot of homeowners only find out their sump pump is not functioning or has malfunctioned when it is already late. A non-functioning sump pump during rainy days could lead to flooding and wet walls. It is recommended to have an extra sump pump just in case the main one malfunctions or at least perform frequent maintenance with the sump pump that you already have.

The installation of the basement waterproofing systems like drainage and sump pumps among others comes with an offer of annual maintenance. It is recommended that you grab this offer to ensure that your sump pump is well maintained to save your basement from damage. Remember that a house that doesn’t get flooded cost higher in the market.

  • Regular maintenance includes the removal of obstructions such as leaves, twigs and stones in the sump pump liner, filter and screen.
  • You have to clean the pump’s inlet screen at least every three to four months. It should not be clogged with debris or residues to maintain the pump’s efficiency.
  • You should also check the power cord. Make sure that it’s plugged correctly to a power source. Inspect the cord and guarantee that it’s in good condition. If it’s already damaged, you should consult a technician to see
  • Speaking of power source, the sump pump should have a backup battery to guarantee that it won’t fail just in case you experience a power outage. Check that the battery is working. Unplug the device from the outlet and see if the battery will power it up.
  • To test if the sump pump is working, pour a bucket of water into the device and observe if its float mechanism will rise. Make sure that the pump will turn on automatically as well.
  • Once a year, perform a thorough check on your sump pump. Remove the device from the sump, clean it and inspect it. Also clean the sump to get rid of residues and other types of dirty substances.
  • After cleaning the sump and the device, get the owner’s manual and check if the device should be oiled or greased. There are models and types of sump pumps that require greasing. If the manual doesn’t indicate anything, use the internet. Go to Google and research about your device using its brand name and model number.
  • Afterward, re-install the device into the sump. Make sure that you’ll connect the power cord properly to the outlet. And to ensure that it will work, use the bucket method. Pour a bucket of water into the sump and check if the device will automatically activate.
  • It is recommended that the sump pump’s drains are flushed with hot water regularly. This method ensures that iron bacteria colonies do not grow and multiply and removes debris that might obstruct the flow of water.
  • Avoid the use of hazardous cleaning chemicals such as ammonia, bleach, detergents and the like in cleaning your sump pump system.

 

SUMP PUMP REPAIR AND MAINTENANCE GUIDE FOR CHICAGO HOMEOWNERS
Additional areas to clean and check:

  • Removable screen at the base
  • Test operation and the float switch
  • Check water discharge lines
  • Open drains
  • Battery backup

Once you have your sump pump installed, it becomes a must to follow factory recommended maintenance procedures. Complete maintenance checks every year, but it is recommended that it is done twice a year.   

How to Use a Sump Pump

24 hour sump pump repair ChicagoMany American homes require sump pumps in order to clear away excess liquid in low-elevation areas where water can easily collect.

Some homes are required by law to have a sump pump, even if they aren’t in a flood zone. Often, this means installing this equipment to prevent flooding in your basement or crawl space.

There are many reasons to take care to keep your home free from flooding. Naturally, keeping your basement dry is important for maintaining it as a storage or living space. Preventing flooding is also good for the longevity of your home, and can prevent damage to your foundation. Removing excess moisture is also essential for preventing the development of mold and mildew.

Regular Check Ups are Needed

If you currently have a sump pump, you should check it regularly to make sure it is running smoothly. During dry periods of the year, you can pour water into the sump to make sure it is still in good working order.

Submersible-type pumps have a screen on the bottom that should be cleaned on a regular basis. Debris collecting in the sump can be the underlying reason for a lot of problems, so it’s essential to make sure debris is carefully cleared away periodically.

If you’re concerned about your pump’s maintenance, this is something that a professional can help you with. Making sure your pump is working properly can save you lots of money on repairs in the future!

Common Sump Pump Repair Problems

sump pump plumber ChicagoYour installed sump pump is permanent and will last years with proper care and maintenance. However, plumbing troubles are always unexpected.  It’s best to know these common sump pump problemsand tips on how to troubleshoot them:

Defective float– The float is an important part of the sump pump because it is the one that triggers it to pump in the first place.

See to it that you also check the float randomly and in between maintenance checks by your plumber in Wellington to see if there are obstructions that will cause problems in the future.

Valve not working– See if the valve is clogged with debris or not. Check the arrow and observe. It should be pointing away from the sump pump and not towards it.

Faulty electric wires– Make sure that the electrical connections are not broken or peeled. Also check the circuit breaker, fuse, and the power source itself.

Sump Pump Not Working? This Might Be Why…

A well-installed and maintained sump pump should last for many years, but if you notice any problems with your pump, here are a few of the common reasons why there might be a problem:

  • Lack of Electricity

If you lose power, obviously your sump pump will stop working… and this can happen at times when you need it to work most. If flooding during storms is an issue for your home, you may want to consider installing a backup generator for your pump. Another option is to install a backup pump that operates on water pressure.

  • Electrical problems

Problems can ensue if your pump is getting too much, or not enough, electrical current. Make sure that your pump is connected to an outlet that provides the proper amount of voltage. Too little can cause the pump to run improperly, and too high of a voltage can cause damage to the motor.

  • Switch Problems

If you have a float switch on your automatic pump, it can become obstructed and cause problems in switching on and off. This is one important reason to ensure that your sump remains as clear of debris as possible.

  • Blocked Discharge Lines

It’s possible that your discharge lines can become blocked by debris, such as rocks or sticks. In winter, your discharge line can freeze. This might be an issue that’s easily solved by manually removing debris, but occasionally it’s a problem that an expert will be able to fix for you.

  • Overworked Pump

Occasionally, your pump may not be working properly because it’s simply overworked. The solution might be to reevaluate the right kind of pump for your home  and to install the appropriate model.

If you notice that your drainage system is not operating properly, you will want to address the problem as soon as possible to prevent potential flooding in your home.

Choose Our Network of Top-Rated Chicago Plumbers for Installation and Maintenance of Your Sump Pump

Our professional plumbers also know how to spot wear and can advise when to replace your pump before it breaks without your knowledge. Calling us before you have a catastrophe on your hand can prevent water damage, financial losses, and irritation. Don’t let your simple sump pump problem grow into a disaster. Don’t risk more damage and money by putting off the repair.

sump pump repairs Chicago IL
We can perform the following:

  • Assess the condition of your Sump Pump
  • Test it and evaluate efficiency
  • Detect and remove debris
  • Replace and repair worn elements or your entire pump
  • Check discharge line opening for any blockage
  • Test the check valve
  • Clean the Impeller

Plumbers 911 is not simply one company, but rather a network of the top professionals in the business. All of our technicians are highly trained and carefully screened, so that you can have peace of mind that only the best are working in your home.

We guarantee that our prices are below your local median price, so you’ll never have to wonder that you’re getting both high quality and great value.  Call us for sump pump repair service in Chicago today!

 

Posted on: December 14, 2018

Top 6 Residential Plumbing Care Tips for Boston Homeowners

Boston plumbersMost people take their plumbing system in Boston for granted. It may work fine today, but the next day, something could go wrong. If not properly maintained and promptly fixed, leaks or broken taps can become worse overtime. 
 
The problem gets bigger when we don’t pay attention to things. Sure, it may seem like a small faucet or a few drops of water here and there. But the real concern is: How much water is it wasting? How much money is thrown away?
 
Plumbing problems, big or small need immediate attention. That’s a fact. As a homeowner, it is also important to know beforehand what to do in case of a plumbing emergency. 
 
Do you know where your home’s water shut-off valve is located? Do you know who to call for help? Do you have basic plumbing tools in case you have to make temporary repairs?
 
Let us help you tick one off your to-do list. When you need an emergency plumber in Boston, call us! We have the best technicians in the area, and you can be sure that our services are of high-quality and reasonably priced.
 
We’ve been recommended by hundreds of residents all throughout the Massachusetts, even in you search for Boston plumber in Yelp. Our professional contractors respect your time and property. From plumbing fixtures to heating maintenance, we’ve got you covered.
 
First, let’s talk about garbage disposals.
 
There is no denying how useful it can be in a kitchen. While it is not completely necessary, this kitchen appliance simply makes cooking and cleaning up less of a hassle.
 
Unfortunately, despite how often the garbage disposal is used, it is one aspect of a kitchen that is often overlooked and dismissed. A broken disposal unit can cause a block in the drainage system which needless to say can be a costly affair.

#1 – What NOT To Put In Your Garbage Disposal

Below are just three tips to maintain and keep a garbage disposal system in tip-top shape.

1. Run the garbage disposal unit regularly. It is important to regularly use the garbage disposal unit. Turning on the system a few times a day can assure that rust does not build up along the blades of the system. Moreover, running the unit regularly prevents waste from accumulating and building up.

jammed garbage disposal in Boston2. Refrain from putting non-biodegradable food into the garbage disposal unit. It is understandable how tempting it is to shove all kinds of garbage into a garbage disposal unit. Not only does it save time, but tossing trash into the unit requires no trash bags and damp paper towels. Unfortunately, a typical garbage disposal system is simply not made to handle non-food materials. Grinding up glass materials, plastic bottles, scrap paper, cigarette butts and grease can cause damage to the garbage disposal unit’s blade and motor.

3. Keep the garbage disposal unit clean. Quite possibly the simplest way to keep a garbage disposal system from breaking down is to clean it every after use if possible. Running the garbage disposal system after pouring a few drops of soap through cold water is a sure-fire way to maintain a perfectly running garbage disposal system.

We can connect you with a 24 hour plumber in MA to work on your plumbing appliances. Check out our service areas, select your city and call us to schedule a service.

Let’s move on to #2, another part of your home that’s mostly taken for granted.. the septic tank!

 #2 – What are the Common Problems in Sump Pumps?

Poor maintenance. A sump pump’s condition should be checked quarterly. Otherwise, you will be put through a great ordeal.

A faulty switch is one of the simplest yet equally annoying mechanical issues with sump pumps. To be safe, clean, adjust, and test your unit on a regular basis to check for problems.

A discharge pipe that is blocked or frozen over will result in a damaging backflow when left unrepaired. A grate will prevent clogs. However, since preventing pipes from freezing has never been realistic, it would be better to install an alternate emergency discharge line as back-up.

Installation fails. The absence of a check valve on the discharge pipe, which can result in water backflow. This will have a domino effect of causing your impeller to have a backward rotation that, in turn, loosens the motor shaft. Your unit may seem to function when it really doesn’t.

Failure to drill an air pressure-relief hole in the discharge pipe, specifically in the middle of the check valve and the pump. The absence of this hole results in the overwhelming build-up of air pressure, which forces your unit to exert itself more than it should. This places a toll on its performance and shortens its lifespan.

Old age. In general, a sump pump has a lifespan of seven to ten years. If your unit is nearing its end, symptoms of old age will start appearing. Once they do, make sure to have it assessed by one of our Boston professionals to see if an immediate replacement is necessary.

Loss of power. Really bad storms and lightning usually results in power outages, rendering your sump pump ineffective. To spare your basement from flooding, purchase and install a backup generator to keep your sump pump up and running as needed.

These two plumbing systems are mostly taken for granted because they’re not seen often, so ensure that you get them regularly checked by calling us today! Ditch the thought of calling a Boston budget plumbing company. We have local Boston plumbers that have over 10,000 hours of training and experience — we already know all plumbing problems and solutions!

Now, let’s talk about something that we use on almost a daily basis, #4: the water heater.

Let’s say you just got a new water heater installed…

You decide to jump in quickly to try it, but to your dismay the water is frigid cold. What might be the problem?

Before you snatch up that phone for a refund, you first need to know that these are common problems and they can be fixed.

#3 – Why Isn’t My Water Heater Working?

Here are some common problems you might encounter with your water heater.

Water is cold
If your water heater runs by electricity, and it is not bringing you hot water after being turned on for some time, the problem may be with the water heating component. Try to check if this is the problem and replace it with a new one.

Another problem may be the thermostat, which is the monitoring device. Water that’s too hot or too cold can be the result of this problem.

Boston Water Heater Installation ServicesLeaking water
This is a common problem for water heaters, when water leaks either from the tip or from the bottom of the appliance. Leaks can be caused by a number of various problems like corrosion.

When water sits in the tubes for long periods, sediment and rust builds up. Eventually, these elements create cracks inside the tubes and the tank itself.

There’s not enough water
Another big problem you might encounter is there is not enough water. When this happens, it’s usually the thermostat that has a problem. Check if the device is properly working and consider the actual temperature of the water to what you can see on the gauge.

A clogged vent can also be the cause of the problem. It may change the normal flow of water from the tubing.

Rusty water
Rusty colored water is usually the cause of a dissolved anode rod. An anode rod is the component of the heater that attracts corrosive elements in the water.

If it is defective, it often emits a sulphuric smell caused by rusting and degradation of the metal. If this is the problem, it might be time to change the anode of the water heater.

Eerie and popping noises
When there is an eerie sound emitting from the water heater, it usually is caused by buildup of sediments inside the tank. Remove the sediments by flushing them out and filling the tank with new clean water.

How Will I Know if My Water Heater Needs Replacement?

  • Listen to clanking or banging noises, which are signs of aging. Typically upon purchase, a residential water heater comes with a five to ten-year warranty. Unless you have made use of it sparingly over the years, it is advisable that you have your water heater replaced after the specified warranty period.
  • Check for leaks. Beware! A water heater tank that leaks is a potentially major headache. Calling us ASAP for assessment will save your walls, flooring, furniture, and the water heater unit itself. Depending on where the leak is coming from, a professional can assist you in determining whether your unit requires minor repairs or replacement.
  • Check if the water produced is hot enough or not. If the heating element and thermostat are not the culprits behind the heating failure, then call our licensed Boston experts to troubleshoot your unit. Expert advice is sounder than speculation.If your unit fails to heat water altogether, it’s an indication of repair or replacement, which our skilled and experienced technicians can make an informed decision on. Consider your hot water usage. Relative to your unit’s age, usage is a big factor in its performance. Even when still far from the end of its warranty period, your unit may suffer from premature aging due to the following:
  • You have a big or growing family. Your area of residence provides only hard water, which results in a buildup of minerals within the tank. This results in a plumbing line obstruction that inhibits your unit’s performance and decreases its life span. If your unit has served its maximum performance to your family in terms of usage, then perhaps it’s high time to let it retire and find a replacement.

Now for the good stuff: DIY Plumbing with #5 –Your toilet!

If you’re in a situation where the water in your toilet just won’t go down. It might be a headache to watch those things float in the water. But do not worry; here are some DIYs for a clogged toilet.

#4- How Do I Unclog My Toilet?

running toilet problem BostonDIY Method #1. The Plunger
Most clogged toilets just need one special tool – the plunger. A good plunger would have an extension flange on the rubber bell-shaped end. It is created to fit toilets better so you can convey more potency to the plunge.

A poor flush means that your toilet drain is completely plugged and does not drain. A slow drain means that flushed water somewhat fills the bowl but does not clean the waste away. The water level remains high, but normally drains after a couple of minutes.

DIY Method #2. Drain Snake
A drain snake is a long wire coil with a corkscrew-like tip that you lodge into the pipe until it comes into contact with the clog. You then turn the snake clockwise so the head of the wire screws through the clog and disjoints it. Or the rubble winds onto the wire so you can dislodge the clog.

DIY Method #3. Vacuum
You can use a wet and dry vacuum to dislodge anything that is causing the clog. You can also use the vacuum to empty water out of the bowl. Put a piece of cloth or an old towel down to seal around the drain.

Turning on the vacuum and trying to suction the clog can be effective for anything hard that was dropped in the toilet bowl.

DIY Method #4. Dishwashing Liquid and Hot Water
You can squirt a small amount of dishwashing liquid in the bowl, and then pour a pot of hot water in the bowl. Let the mixture sit for a couple of minutes before attempting to flush.

The dishwashing liquid will ease out the waste clogging the drain and hot water will soften the clogged matter. This will make it easy for you to flush the toilet once everything settles in.

DIY Method #5. Baking Soda and Vinegar
Baking soda and vinegar can be effective in dislodging anything that clogs a toilet. A cup of baking soda, a cup of white vinegar, and a kettle of hot water poured into the bowl will work instantly to flush the toilet clean.

Then, #6 — Your drains..

If you’ve been standing there waiting for the drain to flush the water out but it’s taking far too long.

This is an initial sign that the toilet or sink could be facing a clogged drain. Basically, if you are cautious of what goes down on your drains, you really shouldn’t clean and clear them of debris recurrently.

The following maintenance is needed to prevent a clogged drain that can be a problem in the future. Some can be done once a week and some about once a month.

#5- How Do You Keep Drains Clog Free?

Once a week maintenance tips:
Bring the pop-up stoppers up in the bathroom sink to get rid of trapped debris, put in in the trash and wash the stopper and put it back in the drain.

Take out the drain cover from the shower of the bathtub drain and use a bent wire or hair catching brush to remove debris that might have collected there.

Drain Cleaning BostonOnce a month maintenance tips:
Clean and clear your waste disposal with a stiff disposer brush or mix a few cups of ice and table salt. This will help remove grease buildup and slime off the sides of the disposer. Flush it with cold water added with lemon to deodorize.

For bathtub maintenance, pull out the overflow plate, and bring the pop-up handle up to grasp the rocker arm. Get rid of accumulated debris and wash thoroughly before setting it back.

It is also advisable to use a good cleaner to protect all the drains in your home. A good cleaner has to be non-corrosive and biodegradable so it won’t deteriorate your home plumbing system. It is better to use a nature friendly cleaner than chemical ones as it can be safe to your plumbing system and your family. Drain cleaning in Boston is one of our expertise, call us for help!

To clean your drains effectively, you can use baking soda and vinegar. This is a great way to help eliminate a slow-moving drain.

To unclog a drain with baking soda and vinegar, use the following tips

1. Let a pot of boiling water run down through the drain.
2. Throw in about half a cup of baking soda. Let it sit for a couple of minutes.
3. Then, pour in a mixture of a cup of vinegar and a cup of hot water.
4. Cover the drain with the plug and let it sit for 5-10 mins.
5. Flush with boiling water.

Lastly and the most basic: Faucet installation.

#6 – How Do I Install a Faucet?

Step 1. Inspect the openings.
Probe the sink for openings and their distance together. Bathroom faucets, in particular, have two handles that may be connected to the spout to form a single unit, or they may be set up apart. This information will be helpful for proper faucet installation or replacement.

Step 2. Turn off the water supply.
There are generally two valves for water supply, one for hot water and another for cold. Turn them off by twisting the valves clockwise to stop water from running in the tubes.

Step 3. Put the faucet replacement in position.

For proper faucet installation:

– Start by positioning the gasket and the faucet on the sink.
– From beneath the sink, thread the mounting nuts into the shanks. Make sure that the flat, wide side part of the mounting nut is up.
– Screw the mounting nuts tight but not too tight to damage it or make it difficult for future replacements.

Step 4. Connect the water supply.
Water is typically supplied by the water-supply tubes. To connect it properly, make sure you take note of the following steps.
Cover the threads of the water supply valve with plumbers tape.
Thread the nut into the shut-off valve and secure with a wrench.
Wrap the faucet shanks threads with plumbers tape and thread the water supply nut against the faucet shanks.
Secure the nut with a wrench.

Step 5. Clean the faucet by flushing.
Make sure that the water supply is clean by running water into the faucet to flush trapped debris off of it. Trapped debris can impair the sealing surfaces inside the faucet and trigger leaks.
Open the water supply valves beneath the sink.
Let water run for 15 seconds to remove residues and trapped particles off the tube.

We’ve covered a whole lot of topics in this blog post, and we hope that you now which one will save you loads of dollars in the end?

However, the decision will always be up to you. Just remember to contact us for any of your plumbing repairs, big or small, because we have licensed, insured and certified Boston contractors on standby, 24/7.

Watch the video below to see why you need to eliminate sub-standard plumbing services and only hire reliable plumbing experts in Boston.

Posted on: October 18, 2018

Troubleshooting and Sump Pump Repair in Berwyn, IL

sump pump repair in Berwyn, ILSump pumps are important in places that are prone to flooding. These are installed in basements to protect the property from water damage when flooding occurs. Hence, a broken sump pump should be repaired immediately. Almost all of the time, the needed repairs are simple and can be done even with little plumbing knowledge. This post will help guide you through troubleshooting and sump pump repair in Berwyn, Illinois. You may be able to apply a thing or two before you call a plumbing professional.

Sump Pump Parts and Their Common Problems

The typical lifespan of a sump pump is about a decade. Regular maintenance checks can do wonders to make a sump pump work efficiently until this time.

Float

The sump pump’s float is the ball-shaped part that rises with the incoming flood water to automatically switch on the pump. Without the float, there will be nothing to trigger the pump and the basement will be flooded. Regularly check your sump pump’s float and make sure that there is no debris that could prevent it from rising or falling. Call a licensed Berwyn plumber immediately if you see that it’s broken.

Valve

An incorrectly installed check valve will cause problems, too. When the check valve doesn’t function properly, water will go back into the basin after the sump pump has shut down. This means more work for the unit which will in turn cause it to break down easily. The check valve should be inspected thoroughly for a build-up of debris. The arrow should also be always pointing away from the pump and not towards it.

Impeller

If the sum pump makes an unusual noise, it is most likely the impeller causing it. A broken impeller should be immediately repaired by a licensed Berwyn plumber. Without it, the entire sump pump will not work. Probable cause is debris build-up. The impeller should be removed and thoroughly cleaned. Then, a filter should be installed after to avoid future debris build-ups.

Electrical Wiring

First, rule out if the inside electrical wiring of the sump pump is the problem or the power supply. Check your circuit breaker if it tripped or not. Then, see if there is a faulty connection. Lastly, inspect if there are broken wires. Once you ruled out this three, and the other parts of the sump pump are working fine, then it is most likely that the electrical wiring inside the unit is the culprit. Never try to repair this problem yourself. Call a plumbing professional immediately to avoid possible electrocution.

Call Plumbers 911 for Sump Pump Repair in Berwyn

Plumbers 911 can help find the perfect licensed Berwyn plumber for you. Plumbers 911 has a comprehensive list of certified plumbers throughout the country. All you have to do is call (855) 484-3911 to ask for a free quote and to schedule an appointment.

Meanwhile, watch this video to know more about Plumbers 911 Illinois:

 

Posted on: November 8, 2017

Plumber in Wellington on Sump Pump Repair and Installation

sump pump plumber in Wellington

The State of Florida has a tropical climate that experiences at least 128 days of rainfall a year. Thus, it is common to hear about basement flooding stories from affected home and establishment owners. The Village of Wellington is no exception. In fact, the city receives 57 inches of rain yearly when the nationwide average is only 39 inches.  Sump pumps are installed in basements of homes prone to flooding. A  professional plumber in Wellington is recommended to install, maintain, and repair sump pumps.

How a Sump Pump Helps to Prevent Basement Flooding

Sump pumps are nifty devices that basically sucks water in and brings it out to your drainage system and away from your property. Normally, sump pumps are installed in the basement of houses and establishments but they can also be placed in other low-lying parts of the house that are prone to flooding. 

There are two types of sump pumps: 

  1. Pedestal Sump Pump – Installed on top of the sump.
  2. Submersible Sump Pump – Placed inside the pit.

Your trusted plumber in Wellington will first dig a pit in the area where your sump pump will be installed. He will check the area and tell you where the best spot to install the sump pump is. He can also recommend the best type of sump pump for your property.

Once our sump pump is installed, you can rest assured that your property will be water-free. It is a worthwhile investment, actually, especially if your place is prone to flooding. 

Call a Reliable Plumber in Wellington to Install Your Sump Pump

Plumbers 911 can help connect you to a licensed Wellington plumber who can install a sump pump in your property.  Call (561) 475-1164 for a free quote and to schedule a visit an appointment.

 

Posted on: August 1, 2017

Sump Pump Repair in Beaumont, Texas

sump pump repair

Basements are common in most American homes, and the ones in Beaumont, Texas are no exception. Basements are one of the most functional rooms in a home. It is commonly used as storage of old items and important mementos. Thus, it becomes important to keep it flood free. This is where sump pumps come in. A sump pump is a plumbing device that sucks in flood water and brings it to a sump basin. In the olden days, a sump pump disposes water to a clean water sewer. 

What a sump pump is

A sump pump is a plumbing device that sucks in flood water and brings it to a sump basin. In the olden days, a sump pump disposes water to a clean water sewer. 

A sump pump automatically turns on when it is filled with water.  Once this happens, it will siphon the liquid and pump it out into a storm drain or your yard. 

A sump pump has two types that can be used at home: pedestal and submersible. Pedestal sump pumps have motors that can be found above the sump. Meanwhile, submersible sump pumps are mounted inside the sump itself. The sump is sealed to ensure that there will be no electrical short circuit failure. 

Sump Pump Maintenance

Sump pumps need to undergo regular maintenance checks to ensure that it will not break down. For 3 to 4 times a year, a sump pump should be cleaned of debris by inspecting its inlet screen.  Next, it should be checked whether the water that is being pumped is disposed of in the appropriate place. To check whether the unit’s sensors are working perfectly, pour a bucket of water into it and see if it activates. Lastly, make sure that the sump pump’s discharge pipe will be alright during the winter months. A vent line should be hooked to prevent clogging.

 Common Problems
 

Here are a few of the most common sump pump problems:

  • Inadequate size
  • Wrong installation
  • Power failure
  • Clogging of discharge lines
  • Switch issues
  • Product factory defects

Should you experience any of these problems, contact your local Beaumont plumber at (409) 237-3137 right away. Plumbers 911 Texas only refers licensed Texas plumbers that can provide reliable sump pump repairs in Beaumont.

Meanwhile, watch this video to know more about Plumbers 911.

 

Posted on: June 27, 2017