Category: Plumbing Repair

6 Ways to Care for Your Pipes in Your Chicago Home

pipe maintenance chicagoHome plumbing, though not recommended to non-professionals, can be achieved if homeowners take extra precautions in performing proper maintenance.

This can be done if you have the proper equipment and skills needed to fix anything on your plumbing system. Simple tasks such as fixing the leaky faucet or replacement of your toilet gaskets can easily be done.

However,  there are more complicated tasks that you should always leave to the experts like pipe replacement and repair.  Below are some tips on how you can avoid these..

How to Avoid Costly Pipe Repairs

Costly plumbing repair service can also be prevented if these easy tasks are performed:

  • Check for leaks – Unmanageable flooding is sometimes caused by leaks because even the smallest leak in your pipes and faucets can cause this. The damage incurred through this require substantial plumbing repair and yes it is oftentimes costly. It is therefore important to check unheated basements, crawl spaces, garages and exterior walls, basically all areas that lack insulation.This is because little to no insulation often leaves pipes vulnerable to elements that make them crack and leak. If you cannot do the checking yourself, contact a residential plumber to help you check trouble areas and provide an overview on how to prepare as well as to maintain your plumbing system in the coming winter months.
  • Weatherproof possible trouble areas – It is always essential to look out for possible trouble areas, normally those with exposed plumbing. Windows, doorways, and vent fans should be checked to ensure that their seals remain tight.Otherwise one can fix up with caulking to prevent your home pipes from freezing. Ensure that cracked windows are repaired because as they can lead to freezing temperatures that would cost you expensive plumbing costs.
  • Insulate exposed pipes – Sealing off all airflow inside your home could lead to mold growth overtime. To avoid this, you can have your pipes properly insulated for them to stand up against cold winter air.This easy and inexpensive procedure is the best way to go. You can try installing foam tubing or wrap towels around your pipes to help the water heater retain heat. The pipes near electrical sources are vulnerable and should be insulated with electrical heating tape. Wrap it around the pipes to provide enough heat and keep the pipes from freezing.
  • Drain and insulate – Outdoor faucets and pipes have to be drained and insulated before the winter season to ensure that the water inside the pipes won’t freeze and expand. This is what’s causing the pipes to crack and burst. Secure the exterior pipes to avoid property damages and costly plumbing repairs.
  • Keep interior pipes warm – Do not forget that even indoor pipes are affected by the winter season. They can also freeze in cold weather. In order for them to not freeze, open your cabinet doors to expose them to heat.If you won’t be home for quite some time, set your thermostat to a minimum of 55 degrees Fahrenheit. You can also let your indoor faucet drip steadily to prevent pipes from bursting.
  • Have a licensed Chicago plumber maintain your pipes for you – Your plumbing system plays a major role in your home hence it needs the best care. Costly repairs can be avoided if the pipes have been properly installed and maintained from the very start.

Burst Pipes in Your Chicago Home? 

burst pipe repair TennesseeThere are two most common causes of broken pipes: water pressure and freezing.

For now..

Let’s talk about water pressure buildup and what you can do to prevent it.

Too much water pressure in your pipes can cause leaks and burst pipes. But how do you know if the water pressure is too high?

If you notice banging noises coming from your pipes, have a running toilet, or if you are experiencing frequent issues with your plumbing appliances, you probably have excessive water pressure in your plumbing system.

To prevent this from happening, have a water pressure regulator installed by a plumbing contractor in Illinois.

Understanding the causes of burst pipes can help you fix issues when they are still manageable and prevent them from occurring. However, once a water pipe in your home bursts, you don’t have much of a choice.

This can cause damage and inconvenience.  It can be costly to repair when not addressed immediately, so the best thing you can do is to have it repaired by our expert professionals right away.

Why You Need To Have Burst Pipes Repaired As Soon As Possible

A cracked pipe that is about to burst is like a ticking time bomb. It can break anytime and cause costly damages, so immediate action is needed. It is always a good idea to fix a damaged pipe as soon as you find them.

A pipe leak, even a small one can cause damages to your home if left undetected. Here are some of the adverse effects of a pipe leak or a burst pipe:

  • Indoor flooding
  • Mold and mildew
  • Water damage
  • Structural Damage

Never let a broken pipe, or a leak get out of hand before calling an expert. While some minor issues are easy to fix, water leaks and burst pipes need immediate professional attention. Make sure to detect cracks and leaks and ensure that proper repairs are carried out. 

Let the Experts at Plumbers 911 Chicago Fix Any Broken Pipes In Your Home

When you call us for help, here are the great things you can expect from us:

  • We offer speedy customer service
  • Technicians will arrive at your doorstep within the hour of your call, guaranteed.
  • Our emergency services are available any time of the day (and night)
  • We only have licensed, fully insured and bonded plumbing specialists
  • All our experts are well-trained and experienced in the industry
  • We offer reliable services that are not overpriced

 

 

Posted on: February 12, 2019

Leaky Faucet Repair Signs and Maintenance Cheatsheet for Chicago Residents

leaky faucet repair ChicagoWe use our faucets every day.  We turn on the tap to wash our hands, cleanse our bodies and wash our veggies. 

A kitchen tap that’s dripping or filled with lime and buildup stains should not be taken for granted. 

If you notice your water faucet leaking or if you need to find out how to fix a leaky bathtub faucet, read on..

In This Article, We Will Be Covering:

  • Removing lime and buildup stains on your faucet
  • Top leaky faucet repair signs to watch out for
  • What shouldbe done to fix your leaky faucet
  • Common leaking tap repair problems
  • Causes of dripping faucet repair problems
  • What to do when your kitchen tap is dripping
  • The how-to’s of shower faucet repair
  • How to fix your leaking outdoor faucet
  • 5 easy steps to fixing your dripping faucet
  • Top 5 kitchen faucet brands that give you bang for your buck
  • Why you should call a professional plumber to help
  • Why call Plumbers 911 for your leaking tap repair

fix leaky faucet ChicagoHow to Remove Lime and Buildup Stains on Your Faucet

Pesky lime and hard-water buildup can be hard to remove and frustrating to work with.  There are several solutions, however, that will dissolve calcium and lime deposits that accumulate over time. 

Just as important though, is to determine if a leaky faucet is causing the buildup.  The stains can be a sign that your faucet is in need of repair.  This article will provide information on how to remove stains and then how to prevent them in the first place.

There are several homemade and store-bought solutions that remove lime and mineral deposits from bathroom and kitchen faucets. 

  • Acids. Acid will dissolve lime and mineral stains.  Acid can be found in household products like vinegar or lemon juice. Simply rub into the stain to dissolve the buildup.  Take care not to leave the acid on for too long, as it may corrode the surface of the faucet or sink. 
  • White vinegar and baking soda. For extremely stubborn stains, mix vinegar and baking soda to create a paste.  Scour the surface using a soft brush or a sponge.  This method is especially good at removing hard water stains. 
  • Commercial Products like C-L-R. Commercial products like C-L-R will remove calcium, lime, and mineral buildup.  Follow all instructions when using these products.

Once stains have been removed, check to make sure that a drip or a leak is not causing the buildup. A drip occurs when the water is turned off.  A leak occurs when the water is on and is leaking out of the base of the spout. 

5 Top Leaky Faucet Repair Signs to Watch Out
For Before Calling Our Chicago Plumbing Experts

It is unfortunate that a lot of people have the habit of ignoring such problems when they perceive that it is still “manageable”. Our contractors are usually called in when the damage is already at its worst. During this time, it is natural that the repair will take more time and other resources to complete.

To avoid a costly and time-consuming restoration job, you should call our specialists immediately once you observe any or most of the following signs of a defective faucet:

bathtub faucet

Water Drip
The sound and sight of water dripping from your tap (when it is supposed to be fully closed) is the most common indication that there is something wrong – either there is extremely strong water pressure in the pipes or the valves are already malfunctioning. 

Regardless of the cause, you should never ignore this with just a mere hope that it will eventually go away because it won’t; unless you do something about it.

Irregular Water Flow
If you no longer experience a steady stream of flowing water but rather a mere few drops followed by spurts of water every few seconds, the aerator may be clogged or there are other issues that need fixing.

Damaged Parts
When you are already having a hard time controlling the flow of water because the handle no longer works properly or some of the components are already falling apart, it is evident that you cannot simply let this matter go.

Corrosion and Mineral Deposits
Rust is probably the most common enemy of this fixture as it is in constant contact with water. Rust and mineral deposits cause damage and if you fail to address it immediately the same could even be irreparable.

Rough faucet handle
A tap handle that is already squeaky or rough can be a symptom of various problems such as worn-down stem, among others.

Unusual Sound
You should be wary of the sound your faucet makes. If you start hearing screeching, clicking, or other weird sounds coming from your faucet then it is a sign of several problems that might be going on not only in the tap itself but even in your home’s plumbing system.

 The items above are just some of the tell-tale signs that are readily observable, which means you can hardly miss them (unless you want to).  

Here’s What Should Be Done to Fix Your Leaky Faucet

Repair drips

  • Replace the washer inside the faucet at the base of the handle. The new washer must be the exact right size, or it will not create an adequate seal to prevent water from dripping out of the handle.  Take the old washer with you to a hardware store in order to purchase the right size washer.

Repair leaks 

  • Replace a faulty O-ring.The O-ring prevents water from leaking out around the spout.  If this ring is deteriorated, water will appear at the base of the faucet spout every time you run the water.  To repair, remove the spout and replace the O-ring with a new ring of the exact same size. Then reassemble the faucet.
  • Make sure the faucet’s packing nut is tightly secured. Install new packing, which is the soft wiring that wraps around the stem of the faucet. Then apply a coat of petroleum jelly on the threads of the stem and the packing nut. 

Addressing them by calling our technicians the moment you notice them will be cost-effective and more beneficial in the end.  Call in one of our expert Chicago plumbers for help.

leaky faucet repair signs and maintenance Chicago

What are the Common Leaking Tap Repair Problems?

  • Dripping Faucets
  • Low Water pressure
  • Loose parts, or worn out seals
  • Valve seat issue

A dripping faucet and low water pressure are just two of the main reasons to replace or repair your kitchen faucet.

Chicago plumbing fixingA Loose or damaged, or improperly installed washer
The washer in the faucet can become dislodged, or become damaged over time. This will cause a leak but is an easy repair for a professional.  If a washer was not installed properly then it will also cause leakage.

Valve seat has become corroded
This provides the connection between the faucet, and the compression mechanisms spout. A corroded valve seat can cause leakage as water sediments can accumulate on the valve. Our professional plumbers can ensure that it is cleaned and not corroded.

O-ring issues
When the O-ring (a small disc attached to the screw that holds the handle in place. If this disc becomes dislodged, breaks, or wears out, then leakage can occur and will be near the handle.

A seal may be worn out- there are two types of seals in a faucet, one that sits near the inlet of the faucet and one that sits near the outlet. If these accumulate sediment; which can happen with regular use, then seals may wear out. Our professional technicians can ensure that the sediments are cleaned from your faucet regularly to help keep them functioning correctly.

Some of your faucet parts are loose
A loose part such at the O-ring, packing nuts, or even a steam screw can happen with general use. Leakage will happen when this occurs and these parts will either need to be replaced, tightened or put back in place to help stop the leakage.

fix leaking tap Chicago4 Causes of Top Dripping Faucet Repair Problems


Bad installation

Most faucet problems can be accounted for during the initial installation. Trying to do the setting up of a new faucet can be well and good if you were able to go by the process with the installation guide.

However, if you just tried to fit it like a jigsaw puzzle, you could eventually miss something which could probably be a big problem in the long run.

Leaks

Leaks are the most common problem with faucets. It is often the most visible problem that one can see to determine if there is an issue. Leaks can originate from various areas including from the aerator, to base of the spout or the underside of the handle.

Repairing leaks can be quite simple and easy. Most of the time, they can be mended with faucet repair parts such as the O-ring which can be damaged quickly.

Sluggish water pressure

Unusual drops in water pressure is also a common problem. Most of the time, this can be caused by an increase of mineral deposits inside the faucet system called lime-scale. Lime-scale problems are more common in houses with hard water supply and can be solved by thoroughly removing the build-up inside the faucet.

Although a sluggish water pressure can be a symptom of a bigger problem. In this cases, Plumbers 911 Chicago can assess the systems and put everything in tip-top shape.

Deterioration and corrosion

Taps deteriorate with constant use. Major segments inside the faucet can start to corrode and grow rust. They can be visibly seen outside, plus the water coming out can be tarnished with rust.

This greatly affects the quality and tolerability of your water supply. Corrosion can be a major problem if the faucet has aged over time.

What to Do When Your Kitchen Tap is Dripping

Do-it-yourself repair can be quite simple to do. You just need basic tools like screwdrivers, a wrench, and a pliers.

  • The initial process goes by turning off the water valve located under the sink and letting the excess water drain from the faucet. Loosen and remove the handle using a wrench.
  • Use the fliers to separate the bonnet. Then take out the ball and cam assembly.
  • A spring is located inside the furnishing. Fish it out with a pliers as well as the packing pieces. It is also good to clean any sediment build up trapped inside.
  • Remove the O-rings and the diverter with pliers and also clean any sediments.
  • Once the faucet face has been cleaned of debris, you can restore the components by putting the new diverter first. Then the new set of O-rings. It is also good if you can coat them with grease to repel high water temperatures.
  • Then put the spout back into place and finish the installation.

The How To’s of Shower Faucet Repair

A leaky shower can waste hundreds of gallon of water if left unrepaired. They can cost much more if you have hot water dripping as they can squander a serious amount of energy. To fix, you need to:

  • Start off by separating the faucet handle from the main system. Newer showers have their screw hidden below the cover cap and the older ones have their screws exposed.
  • Once the cover caps are removed, detach the locking screw by twisting it counterclockwise. Use a faucet puller to remove the handle.
  • Additionally, remove the trim and the sleeve that aligns with the faucet stem. A special device like a deep socket can be used to detach the stem from the valve. Then take the faucet stem and remove it out of the valve.
  • Replace major components like the O-rings, flat washers and seals with a new one.
  • Then reassemble the components back into the shower faucet system. It is also good to use plumber’s grease to oil the threads.

How to Fix Your Leaking Outdoor Faucet

Repairing your outdoor tap can essentially save you much money that can damage your exterior property and eventually leakage in your basement. Fixing it can be simple to do with these tips.

  • The first thing to do is to locate the supply valve which can be typically found in the basement or under the kitchen sink.
  • Remove the spigot by twisting it with a crescent wrench. Check for any problems inside the spigot. The washer may be damaged or is placed improperly inside the spigot. This can be the cause of the problem.
  • Replace the old washer with a new one then affix the valve and handle. Test the new installation for any additional problems.
  • If there are still leaks after replacing the washer, there may be a different problem. Use a wrench to remove the handle and spigot from the faucet again, then turn the packing nut to extract it. Remove the packing nut and take off the faucet valve stem.
  • Look for the washer found at the bottom end of the valve stem and replace it with a new one. Additionally, you can check for what causes the problem such as rust, corrosion or water build-up. You can also apply grease on the packing nut and the washer to lubricate it.
  • Finally, you can attach the spigot and the faucet handle.

faucet installation and servicesHow to Fix Your Dripping Faucet in Five Easy Steps

If you don’t have time to call in one of our expert plumbers, here is what you can do (if you have tools handy in the house)

You will need the following:

Adjustable wrench
Flat-head screwdriver
WD-40 or CRC
Replacement washers and O-rings

Here’s what to do:

  1. The most important step before starting any plumbing job is to make sure that your main water supply is turned OFF. You don’t want to risk flooding your kitchen and getting all wet, do you?
  2. Remove any decorations from the faucet (like fancy handles)You will then see the how the basic faucet looks like. You will notice some knobs once the top part is removed.Under those knobs, you will see the screws that mount the handle to the stem.  
    Remove these and slowly take off the handle with the flat-head screwdriver. You can apply some WD-40 or CRC (oil) to make loosening easier so you could remove the faucet handle from the stem.
  3. Loosen the nut by using your wrench. While doing this, you will also see the stem and take this off too.Some faucet stems can get taken off quickly, while others (depending on the faucet model) can be twisted off. Ensure that you check if you’ve damaged any parts that you’ve removed.
  4. Check the O-ring and the washerbecause these could cause the leak.Remove these and put a replacement.It’s vital that your new washers or O-rings fit accurately. 
    If you are NOT certain, check the seat to find out if the sides would be able to fit a washer that is cone shaped or flat, so you can buy the right kind.  Go to your local home depot or hardware, show them your old O-ring. That way, you can’t go wrong.
  5. Slowly put together the parts, then turn the knob to test if water will run. Once working, check to see if you’ve fixed the annoying drip.

If, after this attempt, you’ve failed to fix your leaky kitchen faucet, don’t waste more time and call us.

Leaky kitchen faucetFaucet Replacement:  Top 5 Kitchen Faucet Brands That Give You Bang for Your Buck

Before you hit the market to purchase a faucet, it is very important that you browse through the best faucet brands available in the market. As a consumer, it’s best to stay educated about ‘what’s hot and what’s not’ in the market.

Choosing the best faucet for you depends on a number of factors the first is installation and repair. How easy will it be for you to install and maintain your chosen faucet? The second is your faucets compatibility with your sink. Also, keep in mind your needs. Do you need it to have a sprayer and soap dispenser and do you prefer one handle or multiple?

Other factors to include the overall design, the warranty, and the material finish. The finish will determine how long the faucet will last you and maintain its original beauty.

A Hasty decision can leave you with an inferior product. So the best way to ensure that you do invest on a high-quality faucet is to purchase it from reputed brands. To help you with this, I have compiled a list of the 5 Top faucet brands available in the market currently:

#1: Delta Kitchen Faucet

Delta as a brand is well known among the consumers. In fact, many consider it the most reputed brand. Faucets manufactured by Delta showcase unique perfection and advanced technologies.

Before bringing the products to the market, Delta takes the time to test its products by turning them both on and off 500,000 times. These tests ensure that their faucets will not leak in the years to come.

Delta also conducts inspections of over 100 faucets on a daily basis manually to ensure that only best quality products are offered to its customers. The Delta kitchen faucets are available in the market with a Limited lifetime warranty.

#2: Moen Kitchen Faucets

Moen is one of the best faucet brands available on the market and offers a wide range of styles choose from. The faucets manufactured by Moen certainly do feature unique style. Customers can choose from; 90-degree faucets, Align, Ascent, Indi, Level, and Modern Pot filler styles. They can also browse by category.

These faucets feature the technology to ensure a perfect balance of water pressure and come in incredibly attractive designs to fit a wide range of budget needs.

#3: Kohler Kitchen Faucets

Kohler is one of the most celebrated consumer goods manufactured globally and has been manufacturing faucets since 1911. Kohler specializes in manufacturing kitchen faucets, engines power accessories, bathroom fittings, and other products.

#4: Kraus Kitchen Faucet

Kraus is also one of the top-rated companies pioneering in the production of high-performing kitchen faucets. The designs of faucets manufactured by this brand feature endless creativity. The brand promises you great quality alongside excellent style inspired by urban craftsmanship. The designs of kitchen faucets by Kraus focus on residential purposes. However, the faucets do offer the durability of commercial level designs.

#5:  Grohe Kitchen Faucets

Grohe kitchen faucets target their consumer groups by offering them product innovation and urban design. The company has also been the recipient of many awards for their impressive faucet designs.

The faucets the company produces are beautiful and feature a specially designed system; hence the company is a leading brand in the industry. The faucets come with patented dream spray technology, which works to refine the spray pattern in the faucet.

The Best Pull-Down Kitchen Faucet

Delta Faucet 9178-AR-DST

Design

The faucet has a teapot design that adds charm to its aesthetics. The model comes in five different colors. All the colors give this faucet its own impression and won’t give you a headache with creating a theme in your kitchen. They come in:

  • Classic stainless steel
  • Champagne bronze
  • Venetian bronze
  • Arctic steel
  • Chrome steel

Functionality

The faucet comes with a high arch spout that has the capacity to swivel a full 360 degrees for functionality. There is only one lever that controls the switching from hot and cold. Adjusting water flow is clear-cut because of the internal technology used

The Best Pull-Out Kitchen Faucet

Kraus KPF-2110

Design

The single lever pull-out faucet has an ergonomic and durable design that will fit every kitchen. The model comes in one color with a 100% solid stainless steel. It does not easily discolor or corrode.

Functionality

Kraus KPF-2110 has two flow settings:

  • Normal flow
  • Spray

The spray feature is conveyed through a 28-inch long nylon braided hose. You simply press the rubber button on top of the spout and when you are finished spraying, the hose will repeal back into the spout.  

The Best Touchless Kitchen Faucet

Moen 7594ESRS Arbor

Design

Moen 7594ESRS Arbor comes in three different colors:

  • Chrome
  • Stainless Steel
  • Bronze

The faucet is ergonomically designed with a high arc pulldown spout and a nifty handle. Temperature adjustment and water flow is adjusted on the single handle it has which makes it perfect for water filling large pans and pots.

Functionality

The faucet is equipped with MotionSense technology which makes running water fast with just a simple hand movement. This makes your job faster and alleviates germs spreading around as you do not have to touch the faucet. The faucet is very versatile as there are several ways of using the faucet by traditional and modern MotionSense Technology.

Why Should I Call a Professional Plumber for My Faucet Repair Issue?

There are a number of reasons people call a professional plumber to handle a specific repair issue they may have. The biggest is that they want it completed correctly. They do not want to buy the items to fix it, not repair it correctly and then still have to call a plumber, it is a waste of money.

leaking tap repair Chicago

Faucet repair is conducted when there is a problem with the fixture that needs to restore it to its former glory as soon as possible. It is important to have fixtures and other plumbing in your home inspected regularly, as to find any issues that should be corrected before causing your water bill to jump in the hundreds. 

Chicago faucet repair

Here’s Why You Should Call Us to Fix Your Leaking Tap

We provide high-quality work.
Our specialists are licensed, highly skilled, and have years of experience to deliver outstanding results. Moreover, they undergo continuous education and training to ensure that they are updated on recent techniques and trends in the industry.

We care about our client’s peace of mind and emotional health.
We take care of everything and will not leave until the entire job is completed successfully so you can just relax, go on with your usual responsibilities, and do the things that you want to do.

We are always available to assist and help.
Our services are available 24/7, even during holidays and major occasions so you don’t have to wait for days to get something done. Whenever you need us, all you have to do is dial our number and will be there immediately.

We place a high regard on customer satisfaction and safety.
Our team of Illinois technicians undergo regular drug tests on top of skills enhancement activities so that you will feel safe when you call us inside your home.

We fully understand our clients’ needs.
Our fees are affordable and our work is reliable which means you are always on the receiving end, in terms of benefits

This just goes to show that calling our expert Chicago contractors to carry out faucet repairs and other plumbing-related work could provide numerous advantages that extend far beyond the actual job. Call us whenever you need help with your plumbing system and we would be more than pleased to assist you.

 

Posted on: November 23, 2018

An Overland Park Homeowner’s Guide on Tips to Plumbing Appliance Maintenance

garbage disposer repair kansasWashing machines, dishwashers, garbage disposals: these are the kinds of things we use every day and don’t realize how much our lives depend on them until they suddenly break.

Our clothes and dishes remain dirty, or maybe (even worse!) there’s a huge flood in our kitchen or laundry room. Suddenly that old reliable machine we trusted isn’t so reliable anymore.

 

In this article, we will be covering:

  • What plumbing appliances are
  • Understanding how they work
  • Avoiding washing machine repair
  • Care for your garbage disposal unit
  • How to deodorize your garbage disposal
  • What you should do when your disposal is clogged
  • How to avoid dishwasher repair
  • Most common problem with dishwashers
  • How to care for your plumbing appliances
  • Should you repair or replace your plumbing appliances
  • 3 plumbing fixtures you cannot live without
  • When you should upgrade your fixtures
  • Why call Plumbers 911 for your repairs and service

What are Plumbing Appliances?

Plumbing appliances are fixtures that are designed to perform special functions. Their operation often depends on the setting of controls of its motors, pressure and temperature sensing instruments, and heating elements.

With their special characteristics and nature of functioning, these plumbing appliances need to be cared for and maintained regularly by a professional such as Plumbers 911.

These should also be repaired, as needed, to ensure their continuous and reliable operation.Thankfully,  we are committed to providing top quality, round-the-clock plumbing services throughout the state of Kansas. If your plumbing appliances cause a situation that must be addressed urgently, Plumbers 911 can respond as quickly as our name suggests.

Local overland park plumbing dishwasher repairUnderstanding Your Plumbing Appliances

The items that fall under the category of ‘plumbing appliance’ are some of the most used elements of your home, ranging from large appliances like washing machines and dishwashers to smaller ones that are easier to overlook, like your garbage disposal.

These appliances should work well for many years with proper maintenance. It’s important to have a basic understanding of how they work so that you can recognize the signs that maintenance is needed. which will save you money over time.

Avoiding Washing Machine Repair

plumbing contractor overland parkTaking proper care of a washing machine is mostly common sense: Always use the appropriate laundry detergent for your machine, and air out the interior after use to prevent mold growing.

But you should also periodically inspect your machine’s ducts and hoses to make
sure that there are no blockages, loose connections, or the faintest signs of small cracks.

Small, nearly unnoticeable problems like these could quickly become much more serious.

Replacing these parts periodically will help ensure that you have no problems with your appliances.

If you’re concerned about doing any of this yourself, a Plumbers 911 technician would be able to assist you with these precautionary measures.

A common problem is buildup in the interior: Especially if you have a high efficiency washing machine, you will want to take particular care to use only “HE” detergent, and to clean the interior rubber gasket periodically to avoid buildup. Failing to do so could require you to replace the gasket.

Garbage Disposer Care

It’s important to keep disposals clean and use them properly to ensure that they operate correctly for a long time and don’t cause blockages to your drain pipe. Blockages can be prevented by regular use and cleaning – running a little dish soap down the drain will do.

Disposing some food waste down your disposal, such as chicken bones, actually has a cleaning effect on your disposal.  Of course, there are some items you should avoid pouring down the drain, such as animal fats and other oils that can accumulate in your pipes over time, causing blockages.

How to Deodorize Your Garbage Disposal

If your disposal has some unpleasant odors, these can be solved by putting citrus fruit slices or peels down the disposal. Vinegar can also help when your disposal is in need of a thorough clean.

What Should You Do When Your Garbage Disposal is Clogged?

A common problem is a backed-up garbage disposal: this is often actually a clogged kitchen drain line, caused by overworking the plumbing.  

Remember, never put your hand directly down the drain to clear a blockage, and use a tool to retrieve lost items instead. If you have a serious blockage, a plumbing expert from Plumbers 911 can help!

Avoiding Dishwasher Repair

Thankfully dishwashers are relatively low-maintenance appliances, but like all others they should be regularly inspected and cleaned to ensure that they continue to function properly.

dishwasher service Overland parkLike with a washing machine, you should check the gaskets for any cracks that might cause leaks in the future. Replace these parts as necessary to prevent larger problems.

Don’t forget to inspect the sprayer arm to make sure that it isn’t clogged. If there are any blockages, you can use vinegar to help clean them away.

This will make sure your dishwasher runs as efficiently as possible, and will help avoid larger problems in the future. Your dishwasher likely also has a filter for catching food waste, and this should also be cleaned periodically.

What is the Most Common Problem with Dishwashers?

A common problem is a backed-up dishwasher: This can cause flooding in your kitchen, so it’s important to fix quickly! It may simply be caused by food buildup inside the machine.

Make sure to turn off the electricity before you investigate for safety. If you’re unsure about the cause, or if the backup isn’t caused by a simple blockage, contact us immediately to address the problem professionally.

How Should I Care for My Plumbing Appliances?

The plumbing system of your home is almost life the bloodline of your household. Any problems occurring in the system can cause major chaos in your household. It may be a complicated task to locate the problem in the complex network of your water supply comprising of pipes, vent pipes, drain pipes and others.

Because plumbing is a very complicated, and one of the costliest systems to install or repair at home, most of us prefer to call a professional and seek their guidance to resolve the issue.

However, if you follow certain basics and update yourself about the fundamentals of a plumbing system, you can efficiently locate the problem of your plumbing system and take care of it.

How Can You Take Care of Your Plumbing Appliances?

Investigate what’s troubling your plumbing system

When the problem occurs in your plumbing system you have to have a keen eye to look out where the problem lies. Even a small leak can lead to great problems.

Hence, it is very important for you to be alert to notice the signs of impending plumbing failures. Being alert and informed is the first tip that you must follow in order to take care of the plumbing appliances.

If you locate a problem, repair it at an early stage

Ignoring a minor problem you noticed in your plumbing system can lead to serious problems. For instance, if you notice a leaking faucet, repair it immediately to keep your house clean, and not encourage the spread of mold or mildew.

Know where to go in the event of a serious problem

Should the plumbing system in your house fail, here is what you can do. Locate the position of the main shut-off valve in your water supply to stop the home water supply.

If the valve is unreachable, do not take chances be ready with your tools that you need to quickly shut off the water supply.

Spot the sewer valve

To maintain your plumbing appliance, the first thing you need to stay aware of is the location of your sewer valve. This can help you to correct clogging in sewer line.

The knowledge about the sewer valve location will also save you the cost that otherwise you may have had incurred with plumbers taking unimaginable time searching for it.

Train yourself to take on small problems

If you have a few fundamental tools at your home and you know the basic of a plumbing system, you can easily take care of the insignificant plumbing emergencies that may occur. All you need is a quality plunger and sewer snake and a pipe wrench in your tool kit, to resolve such small plumbing problems.

Clean your drains and use them properly

need garbage disposal repair expert Overland ParkThe most frequent problem plumbers address is clogged or slow draining drains. This problem can easily be avoided by regularly cleaning your drains using the proper tools such as a Flexi-snake or a homemade cleaning solution.

Maintaining your drains free of hair and debris will prevent a clog from forming. You can also avoid brushing long hair over the sink to minimize the amount of hair that goes down the sink.

Make sure you treat your plumbing appliances correctly. Many overestimate the power of their garbage disposal and overtax it leading to a blockage.

Avoid feeding it hard items, dried pasta, or too many items at once. Also, do not leave food sitting in the sink overnight as it may harden and create a problem the next time you go to use the disposal system.

Should You Repair or Replace Your Appliances?

If your plumbing appliances require costly repairs, it may be time to replace them rather than fix them.

Even if your appliances are not in urgent need of repair, there are many reasons why you might consider replacing them for updated models.

Progress in technology means that newer plumbing appliances are capable of more features than ever before, offering you convenience. Updated washing machines and dishwashers run more quietly, improving the quality of life in your home, and can use water more efficiently, meaning that you save money while protecting the environment.

If you’ve chosen to upgrade your plumbing appliances, contact our local Overland Park plumbers to have an expert assist you with proper installation.

3 Plumbing Fixtures You Couldn’t Live Without

There is definitely not a day when you do not need a plumbing appliance. It has become an unnoticedmechanism that is generally important to humans.

So, what are the top 3 plumbing appliances that you can’t live without?

Sinks

A sink is a plumbing item that is bowl shaped and is mostly used for washing dishes, small pets, andhands.

clogged kitchen sink drain overland parkSinks can also come in different shapes and varieties. It is sometimes referred to as a basin andmost of the time there are several sinks in a household.

A sink will normally have a faucet that gives either hot or cold water and oftentimes comes with a sprayto give a constant stream of water. Sinks typically have drains and often has a soap dispenser.

The major problem with sinks is they can get obstructed with soap, debris and gunk that get stuck in thepiping. It is often easy to remove the clog for yourself but for severe cases, you have to get the help of aprofessional.


Bathtubs

tub clogged Overland ParkWho can’t live without one? A bathtub is a considerable container that is filled with hot or warm waterand allows a person to bathe at the same time as being immersed in water.

A bathtub is normally foundin the bathroom and sometimes has a shower connection that allows a person to take a shower whilestanding in the bath.

Modern bathtubs are built of fiberglass and acrylic although pricier and more durable ones are made ofenamel, steel, or cast iron. Modern bathtubs are constructed with overflows and drains to reinforce thedraining and delivery of water.

Showers

A shower is a plain plumbing fixture that has a nozzle to stream hot or cold water. The normal showerhas remained consistent and unchanged since the late 19th century. The fixture nozzle can be replacedand changed to yield different pressures, however, the concept remains unchanged.

When Should I Upgrade My Plumbing Fixtures and Appliances?

Simple upgrades to your plumbing appliances and fixtures could save you hundreds.  Upgrading can make your home much more water-efficient and the result is a smaller global footprint and a smaller water bill.  Consider upgrading these household plumbing products to save water and money.

Toilets

Toilets made before 1992 use more than twice the amount of water that new, high efficiency toilets do.  Buying a new toilet can save you approximately $2000 over the life of the toilet.

Showerheads

Replace old showerheads with new low-flow fixtures.  New-generation fixtures labeled “low-flow” use 2.5or fewer gallons of water per minute.  Switching to a low-flow fixture can save you money instantly. And the new models have high-performing options, so a low-flow fixture can provide a luxurious experience.  

Additionally, consider installing an on-demand hot water system or a re-circulating pump for your existing tank.  This can eliminate the need to run water before the shower to heat it up, saving water and money.

Faucets

Upgrading bathroom and kitchen faucets with low-flow models and aerators could save more over 4,000 cups of drinking water.  New low-flow designs are available, so you can upgrade your water-efficiency and your home’s look with a faucet upgrade.

Washing Machines

Energy Star washing machines can save 7,000 gallons of water a year.  Replacing an old machine with a high-efficiency, frontloading washer is an investment that uses half the water of less efficient models.

Dishwashers

You can save over 400 gallons of water a year by using a high-efficiency, Energy Star dishwasher rather than washing and rinsing your dishes by hand.  Energy Star models conserve water and don’t require any pre-rinsing, saving you time and money.

Plumber in Overland parkWhy Plumbers 911?

We will be happy to assist you with questions about water conservation, appliance and fixture installation, and strategies to reduce water use.  We can also help you design an energy- and water-efficient kitchen or bathroom.

As you can see, installing or repairing a plumbing system is not for a weekend hobbyist. It takes education, training, experience and skill to perform a professional job in this industry.

Our experienced techs will answer and discuss all options of your particular plumbing repair in question. We want you to feel secure knowing all the options of what may or may not be the best choice for your particular situation. This is where our experience and knowledge stands out above all others.

Repairs are done only when they will actually solve the problem. Some repairs may include replacing a toilet hose or a part in the tank itself. A leaking faucet can easily be repaired as well.

A complete replacement is a major decision and is not taken lightly, but you will defiantly understand the pros and cons of repairing or replacing a faucet or appliance.

Replacements can be done just as efficiently as most repairs. Our techs also can accommodate around your schedule and make the installation as quick as possible. We know communication is big key for all parties involved.

Our Licensed and Insured Overland Park KS Technicians are Available 24/7

Plumbers 911 is a great name to remember when the time comes to fix or replace your plumbing appliances.  Instead of contacting a single plumber, you’ll be accessing an entire network of top industry professionals.

Every expert affiliated with us is trained to the highest standard and fully licensed. For plumbing work in Overland Park, there’s no better place to turn.

 Overland Park PlumberWe provide a top rated service with a courteous professional staff that is available for all your residential plumbing needs in the KS  area.

We have been servicing our customers for years and have a great reputation for our great quality of service.

Getting an estimate is quite simple with just a quick call. Understanding what exactly you will be getting in return is our priority, as well as yours. We can easily analyze the situation and plan the best direction and the next step.

Prevention just takes a little care and attention to your home and how your plumbing functions. We take into consideration the size of your home and your family size when reviewing prevention options.

Our experts can help you analyze your home and set up the appropriate prevention plan to suit your budget and your particular plumbing needs.

Training and experience is crucial in the plumbing repair industry and our techs have the knowledge needed to accommodate all our customer’s needs. Our training is kept up to date with new innovations that arrive daily. Being well-versed keeps our customers better informed and helps with all the necessary decisions of repairs.

We know that any plumbing problem needing repair is never considered too small. Any major issues started out small and was either not noticed or put on the back burner.  Our training and experience ranges from fixing a drip to a complete new installation or replacement.

Kansas residents know they are getting true professional plumbing technicians when calling us. Our techs and trucks are well equipped to handle all your immediate plumbing needs. We pride ourselves on repeat business with our satisfaction guarantee.

Emergency Service Advantages

Our experienced Overland Park plumbing techs are known area wide for great satisfaction and immediate emergency service. Emergency service to us means 24 hours a day every day, even on weekends and holidays. Emergencies don’t take a break and neither do we. Do not wait when you have an emergency pertaining to any of these situations:

  • Clogged garbage disposer
  • Leaky pipes
  • Sewer backup
  • Clogged drains
  • Plumbing appliance repair
  • Plumbing fixture replacement

One call  and we will be on our way to clean up the messy clogs, fix that leaky pipe, or get you sewer working great again. All these are stress issues and our techs understand how important time is on repairing these problems immediately.

expert local Kansas City plumber

 

These situations can be messy and a major interruption in your daily routine. Our trained professionals handle our clients with respect and compassion.

Sleep better at night knowing that you have done all you can to assure your home is kept safe and sound. Let our specialized techs assist in setting up the right maintenance plan for you. 

Plumbers 911 is ready to help and waiting for your call.

Posted on: November 10, 2018

Top 6 Residential Plumbing Care Tips for Boston Homeowners

Boston plumbersMost people take their plumbing system in Boston for granted. It may work fine today, but the next day, something could go wrong. If not properly maintained and promptly fixed, leaks or broken taps can become worse overtime. 
 
The problem gets bigger when we don’t pay attention to things. Sure, it may seem like a small faucet or a few drops of water here and there. But the real concern is: How much water is it wasting? How much money is thrown away?
 
Plumbing problems, big or small need immediate attention. That’s a fact. As a homeowner, it is also important to know beforehand what to do in case of a plumbing emergency. 
 
Do you know where your home’s water shut-off valve is located? Do you know who to call for help? Do you have basic plumbing tools in case you have to make temporary repairs?
 
Let us help you tick one off your to-do list. When you need an emergency plumber in Boston, call us! We have the best technicians in the area, and you can be sure that our services are of high-quality and reasonably priced.
 
We’ve been recommended by hundreds of residents all throughout the Massachusetts, even in you search for Boston plumber in Yelp. Our professional contractors respect your time and property. From plumbing fixtures to heating maintenance, we’ve got you covered.
 
First, let’s talk about garbage disposals.
 
There is no denying how useful it can be in a kitchen. While it is not completely necessary, this kitchen appliance simply makes cooking and cleaning up less of a hassle.
 
Unfortunately, despite how often the garbage disposal is used, it is one aspect of a kitchen that is often overlooked and dismissed. A broken disposal unit can cause a block in the drainage system which needless to say can be a costly affair.

#1 – What NOT To Put In Your Garbage Disposal

Below are just three tips to maintain and keep a garbage disposal system in tip-top shape.

1. Run the garbage disposal unit regularly. It is important to regularly use the garbage disposal unit. Turning on the system a few times a day can assure that rust does not build up along the blades of the system. Moreover, running the unit regularly prevents waste from accumulating and building up.

jammed garbage disposal in Boston2. Refrain from putting non-biodegradable food into the garbage disposal unit. It is understandable how tempting it is to shove all kinds of garbage into a garbage disposal unit. Not only does it save time, but tossing trash into the unit requires no trash bags and damp paper towels. Unfortunately, a typical garbage disposal system is simply not made to handle non-food materials. Grinding up glass materials, plastic bottles, scrap paper, cigarette butts and grease can cause damage to the garbage disposal unit’s blade and motor.

3. Keep the garbage disposal unit clean. Quite possibly the simplest way to keep a garbage disposal system from breaking down is to clean it every after use if possible. Running the garbage disposal system after pouring a few drops of soap through cold water is a sure-fire way to maintain a perfectly running garbage disposal system.

We can connect you with a 24 hour plumber in MA to work on your plumbing appliances. Check out our service areas, select your city and call us to schedule a service.

Let’s move on to #2, another part of your home that’s mostly taken for granted.. the septic tank!

 #2 – What are the Common Problems in Sump Pumps?

Poor maintenance. A sump pump’s condition should be checked quarterly. Otherwise, you will be put through a great ordeal.

A faulty switch is one of the simplest yet equally annoying mechanical issues with sump pumps. To be safe, clean, adjust, and test your unit on a regular basis to check for problems.

A discharge pipe that is blocked or frozen over will result in a damaging backflow when left unrepaired. A grate will prevent clogs. However, since preventing pipes from freezing has never been realistic, it would be better to install an alternate emergency discharge line as back-up.

Installation fails. The absence of a check valve on the discharge pipe, which can result in water backflow. This will have a domino effect of causing your impeller to have a backward rotation that, in turn, loosens the motor shaft. Your unit may seem to function when it really doesn’t.

Failure to drill an air pressure-relief hole in the discharge pipe, specifically in the middle of the check valve and the pump. The absence of this hole results in the overwhelming build-up of air pressure, which forces your unit to exert itself more than it should. This places a toll on its performance and shortens its lifespan.

Old age. In general, a sump pump has a lifespan of seven to ten years. If your unit is nearing its end, symptoms of old age will start appearing. Once they do, make sure to have it assessed by one of our Boston professionals to see if an immediate replacement is necessary.

Loss of power. Really bad storms and lightning usually results in power outages, rendering your sump pump ineffective. To spare your basement from flooding, purchase and install a backup generator to keep your sump pump up and running as needed.

These two plumbing systems are mostly taken for granted because they’re not seen often, so ensure that you get them regularly checked by calling us today! Ditch the thought of calling a Boston budget plumbing company. We have local Boston plumbers that have over 10,000 hours of training and experience — we already know all plumbing problems and solutions!

Now, let’s talk about something that we use on almost a daily basis, #4: the water heater.

Let’s say you just got a new water heater installed…

You decide to jump in quickly to try it, but to your dismay the water is frigid cold. What might be the problem?

Before you snatch up that phone for a refund, you first need to know that these are common problems and they can be fixed.

#3 – Why Isn’t My Water Heater Working?

Here are some common problems you might encounter with your water heater.

Water is cold
If your water heater runs by electricity, and it is not bringing you hot water after being turned on for some time, the problem may be with the water heating component. Try to check if this is the problem and replace it with a new one.

Another problem may be the thermostat, which is the monitoring device. Water that’s too hot or too cold can be the result of this problem.

Boston Water Heater Installation ServicesLeaking water
This is a common problem for water heaters, when water leaks either from the tip or from the bottom of the appliance. Leaks can be caused by a number of various problems like corrosion.

When water sits in the tubes for long periods, sediment and rust builds up. Eventually, these elements create cracks inside the tubes and the tank itself.

There’s not enough water
Another big problem you might encounter is there is not enough water. When this happens, it’s usually the thermostat that has a problem. Check if the device is properly working and consider the actual temperature of the water to what you can see on the gauge.

A clogged vent can also be the cause of the problem. It may change the normal flow of water from the tubing.

Rusty water
Rusty colored water is usually the cause of a dissolved anode rod. An anode rod is the component of the heater that attracts corrosive elements in the water.

If it is defective, it often emits a sulphuric smell caused by rusting and degradation of the metal. If this is the problem, it might be time to change the anode of the water heater.

Eerie and popping noises
When there is an eerie sound emitting from the water heater, it usually is caused by buildup of sediments inside the tank. Remove the sediments by flushing them out and filling the tank with new clean water.

How Will I Know if My Water Heater Needs Replacement?

  • Listen to clanking or banging noises, which are signs of aging. Typically upon purchase, a residential water heater comes with a five to ten-year warranty. Unless you have made use of it sparingly over the years, it is advisable that you have your water heater replaced after the specified warranty period.
  • Check for leaks. Beware! A water heater tank that leaks is a potentially major headache. Calling us ASAP for assessment will save your walls, flooring, furniture, and the water heater unit itself. Depending on where the leak is coming from, a professional can assist you in determining whether your unit requires minor repairs or replacement.
  • Check if the water produced is hot enough or not. If the heating element and thermostat are not the culprits behind the heating failure, then call our licensed Boston experts to troubleshoot your unit. Expert advice is sounder than speculation.If your unit fails to heat water altogether, it’s an indication of repair or replacement, which our skilled and experienced technicians can make an informed decision on. Consider your hot water usage. Relative to your unit’s age, usage is a big factor in its performance. Even when still far from the end of its warranty period, your unit may suffer from premature aging due to the following:
  • You have a big or growing family. Your area of residence provides only hard water, which results in a buildup of minerals within the tank. This results in a plumbing line obstruction that inhibits your unit’s performance and decreases its life span. If your unit has served its maximum performance to your family in terms of usage, then perhaps it’s high time to let it retire and find a replacement.

Now for the good stuff: DIY Plumbing with #5 –Your toilet!

If you’re in a situation where the water in your toilet just won’t go down. It might be a headache to watch those things float in the water. But do not worry; here are some DIYs for a clogged toilet.

#4- How Do I Unclog My Toilet?

running toilet problem BostonDIY Method #1. The Plunger
Most clogged toilets just need one special tool – the plunger. A good plunger would have an extension flange on the rubber bell-shaped end. It is created to fit toilets better so you can convey more potency to the plunge.

A poor flush means that your toilet drain is completely plugged and does not drain. A slow drain means that flushed water somewhat fills the bowl but does not clean the waste away. The water level remains high, but normally drains after a couple of minutes.

DIY Method #2. Drain Snake
A drain snake is a long wire coil with a corkscrew-like tip that you lodge into the pipe until it comes into contact with the clog. You then turn the snake clockwise so the head of the wire screws through the clog and disjoints it. Or the rubble winds onto the wire so you can dislodge the clog.

DIY Method #3. Vacuum
You can use a wet and dry vacuum to dislodge anything that is causing the clog. You can also use the vacuum to empty water out of the bowl. Put a piece of cloth or an old towel down to seal around the drain.

Turning on the vacuum and trying to suction the clog can be effective for anything hard that was dropped in the toilet bowl.

DIY Method #4. Dishwashing Liquid and Hot Water
You can squirt a small amount of dishwashing liquid in the bowl, and then pour a pot of hot water in the bowl. Let the mixture sit for a couple of minutes before attempting to flush.

The dishwashing liquid will ease out the waste clogging the drain and hot water will soften the clogged matter. This will make it easy for you to flush the toilet once everything settles in.

DIY Method #5. Baking Soda and Vinegar
Baking soda and vinegar can be effective in dislodging anything that clogs a toilet. A cup of baking soda, a cup of white vinegar, and a kettle of hot water poured into the bowl will work instantly to flush the toilet clean.

Then, #6 — Your drains..

If you’ve been standing there waiting for the drain to flush the water out but it’s taking far too long.

This is an initial sign that the toilet or sink could be facing a clogged drain. Basically, if you are cautious of what goes down on your drains, you really shouldn’t clean and clear them of debris recurrently.

The following maintenance is needed to prevent a clogged drain that can be a problem in the future. Some can be done once a week and some about once a month.

#5- How Do You Keep Drains Clog Free?

Once a week maintenance tips:
Bring the pop-up stoppers up in the bathroom sink to get rid of trapped debris, put in in the trash and wash the stopper and put it back in the drain.

Take out the drain cover from the shower of the bathtub drain and use a bent wire or hair catching brush to remove debris that might have collected there.

Drain Cleaning BostonOnce a month maintenance tips:
Clean and clear your waste disposal with a stiff disposer brush or mix a few cups of ice and table salt. This will help remove grease buildup and slime off the sides of the disposer. Flush it with cold water added with lemon to deodorize.

For bathtub maintenance, pull out the overflow plate, and bring the pop-up handle up to grasp the rocker arm. Get rid of accumulated debris and wash thoroughly before setting it back.

It is also advisable to use a good cleaner to protect all the drains in your home. A good cleaner has to be non-corrosive and biodegradable so it won’t deteriorate your home plumbing system. It is better to use a nature friendly cleaner than chemical ones as it can be safe to your plumbing system and your family. Drain cleaning in Boston is one of our expertise, call us for help!

To clean your drains effectively, you can use baking soda and vinegar. This is a great way to help eliminate a slow-moving drain.

To unclog a drain with baking soda and vinegar, use the following tips

1. Let a pot of boiling water run down through the drain.
2. Throw in about half a cup of baking soda. Let it sit for a couple of minutes.
3. Then, pour in a mixture of a cup of vinegar and a cup of hot water.
4. Cover the drain with the plug and let it sit for 5-10 mins.
5. Flush with boiling water.

Lastly and the most basic: Faucet installation.

#6 – How Do I Install a Faucet?

Step 1. Inspect the openings.
Probe the sink for openings and their distance together. Bathroom faucets, in particular, have two handles that may be connected to the spout to form a single unit, or they may be set up apart. This information will be helpful for proper faucet installation or replacement.

Step 2. Turn off the water supply.
There are generally two valves for water supply, one for hot water and another for cold. Turn them off by twisting the valves clockwise to stop water from running in the tubes.

Step 3. Put the faucet replacement in position.

For proper faucet installation:

– Start by positioning the gasket and the faucet on the sink.
– From beneath the sink, thread the mounting nuts into the shanks. Make sure that the flat, wide side part of the mounting nut is up.
– Screw the mounting nuts tight but not too tight to damage it or make it difficult for future replacements.

Step 4. Connect the water supply.
Water is typically supplied by the water-supply tubes. To connect it properly, make sure you take note of the following steps.
Cover the threads of the water supply valve with plumbers tape.
Thread the nut into the shut-off valve and secure with a wrench.
Wrap the faucet shanks threads with plumbers tape and thread the water supply nut against the faucet shanks.
Secure the nut with a wrench.

Step 5. Clean the faucet by flushing.
Make sure that the water supply is clean by running water into the faucet to flush trapped debris off of it. Trapped debris can impair the sealing surfaces inside the faucet and trigger leaks.
Open the water supply valves beneath the sink.
Let water run for 15 seconds to remove residues and trapped particles off the tube.

We’ve covered a whole lot of topics in this blog post, and we hope that you now which one will save you loads of dollars in the end?

However, the decision will always be up to you. Just remember to contact us for any of your plumbing repairs, big or small, because we have licensed, insured and certified Boston contractors on standby, 24/7.

Watch the video below to see why you need to eliminate sub-standard plumbing services and only hire reliable plumbing experts in Boston.

Posted on: October 18, 2018

Frequently Asked Questions on Plumbing

Plumbing is a very common task and almost every home has a plumber that they rely on. Homeowners mostly have lot of queries related to plumbing and this article shall actually help you to get the answers.

  1. What causes pipe corrosion? :

There are a number of things that can lead to pipe corrosion and all are related to the water quality. The causes are:

  • The PH of water
  • Chemicals found in water
  • The temperature of water
  • Oxygen found in water
  • The water pressure
  1. How do I check leaks?

There is a very simple way to check for a leak. Note the water meter and record the water level. Do not use water for few hours and now check once again. This can be done best late at night or very early in the morning. If the water level changes, there is a leak maybe. Call a plumber in Chicago mmediately.

  1. Are hidden leaks anything to worry about?

Yes, definitely because leaks get bigger with time but they don’t cause heavy damage to your home. Know the benefits of leak detection and repair:

  • Elimination and reduction of water loss
  • Less risk of damage
  • Won’t need sudden emergency repairs
  • Less need for pressurization and water treatment
  1. Why is there so much noise in my toilet when I flush?

If there more noise while flushing, it means that water flowing to the tank is somehow getting restricted while refilling due to faulty or broken parts.

  1. How can I prevent my pipes from freezing?

When the temperature dips down to -32 degrees and less, there are chances that Frozen Pipe Repairyour pipeline water is freezing. Frozen water turns into ice which can lead to bursting of the pipelines. Before cold water sets in, drain the valves outside and shut off the interior valve. You can also install a faucet insulator.

  1. What all can and what can’t go down garbage disposal?

A garbage disposal can endure a lot but don’t let them it to be invincible. Always run cold water down the disposal to clear residue and oils seated in the system. Don’t throw anything big, chop into small pieces before disposal. Avoid disposing coffee grinds to prevent build ups.

  1. Why is my toilet running constantly?

While flushing your toilet, a lever function causing a flap to open in the tank and the water level pushes back when it comes back to position. There is a chain attached to the flapper and if that is either too short or long then it might cause a running toilet or flushing dysfunction.

  1. What is the cause of my heater’s relief valve leaking?

The relief valve can leak due to the high pressure that comes from your water heater. Here are the reasons:

  • The water pressure of the incoming water from the main line is very high
  • The pressure is building up due to thermal expansion.

The best way is to call a plumber!!

  1. What would I do with an overflowing toilet?

If there is a leak in the fill valve of your tank there can be a leak and for any other reason, call a professional plumber.

Conclusion 

Now that you have the answers to most of your FAQ’s on plumbing, get in touch with a professional plumber. Call the agency for a scheduled maintenance because your plumbing needs to be looked after.

Posted on: April 25, 2018