Category: 24 Hour Plumbing Service

How to replace a kitchen mixer tap in your Chicago Home

Kinsey new kitchen tap installAre you having problems with your kitchen mixer tap in your Chicago home? It could be leaking or the taps could be showing up other issues. In case you are planning to revamp your kitchen, you would definitely want to replace them. Almost all modern kitchens have mixer taps which deliver both hot and cold water through one single pipe.

The water flowing out is very comfortable to use in the cold season. Every tap comes with a thread of half-inch at the bottom and a small size washer that goes to the bottom of the sink and is fitted with a tiny nut. Majority mixer taps have foam plate which is placed just beneath the unit and this seals the tap very well.

You can connect tap pipes using different methods and the flexible type is really good, the one that has a little rubber seal on it. It’s very simple and easy to fit because the pipes need not be entirely lined up. You can also opt for a rigid tap connector about half an inch but it has a small collar with a rubber washer or a fiber washer.

How to remove the old kitchen tap

First you need to remove the part of the tap that is present down under the sink so that the pipe connectors are visible and access them at ease. So here are the steps:

  • Cut off the water supply and the water supply should be turned off –This is pretty simple so find out the shut-off valve and turn off the water supply. Turn on the taps and check whether the water supply is off.
  • Take off the old tap – If you are not an expert you can call our skilled technicians in Chicago to do so. We have specialized tools for disconnecting taps like claws and tube spanners that help to disconnect swiftly.
  • Disconnecting tap from the main –You have to disconnect the tap from the main connection and it can be done simply by unscrewing.
  • Remove the debris –Clean off any debris that is stuck to the old tap.

Fitting the new mixer tapkitchen sink plumbing

It is easy to fit a new mixer tap, you need to make sure that you have installed it correctly and the seals are just right so that there are no leaks. It is better to call our experienced plumber if you want the best fitting.

Here are the steps:

Fitting the mixer tap on the upper side of the sink –  Firstly, scrub the sink area well to clear off the debris that had accumulated while the old tap was fitted. It’s not a difficult task as you need to slot the pipes in the sink through the holes and the rest of it you need to fix from under the sink.

Connect the tap right under the sink – Take the plastic nut and the rubber washer, get under the sink with these. Use a tool to tighten the tap and make sure the tap does not wobble as you start using it.

Connect the tap to water pipes – Connect the water pipes once again but do not forget to replace the o-rings and washers. The seal is of utmost importance make sure its water tight seal. You might use a tape as well.

Turn on water flow – Now turn on the new tap and see water flowing well. Please check for leaks beneath under the sink and tidy up the place.

It is relatively easy to fit a new mixer tap by removing an old one. There are clients who wish to take a DIY initiative as they have the experience and the right set of tools. But you can always get in touch with our reputed plumbing network in Chicago for new fittings, repairs and replacement. Most of us don’t have time to do such things and this is why we are there to provide you assistance.

Posted on: July 23, 2018

Clearing the Gutter can make a Big Difference in Drainage Bills in Your Kansas Home

Olathe drain cleaningUsually, the gutter always remains out of sight and out of mind unless one day you need to spend a fortune on drainage costs and property repairs.

Modern buildings come with an effective guttering system but it needs to be looked after. Do not ignore if rain water overflows from your gutter, instead take immediate action. Clearing the gutter at proper time can really make a big difference in your drainage bill !

Gutter is a very important part of the house, though not at all glamorous. A lot of homeowners think of clearing their gutters during the fall season but taking care of it round the year keeps your property mainly the foundation and the roof in good health.

Proper gutter system handles the rain water effectively without letting it to spill off the roof,thus preventing the home from moisture damage. Usually debris and leaves can clog the gutters; it can lose its alignment or get separated from the drainage spouts.

When gutters get blocked, it can lead to ice dams that cause roof leaks and in case the gutters are not channeling in a proper way, it can cause spilling and then gradual rotting. Not having clean gutters in the monsoon can cause havoc drainage issues. In the autumn, when the trees shed their leaves, you must clean the leaves so that they don’t flow down from your gutter creating a clog.

Problems in guttering could lead to damp patches maybe in any of the bedrooms or in the corner of the stairs or in part of the house. Once you fix the guttering issue by our expert technicians in your Kansas City, leave the place dry and then re-decorate.

Vacuuming is the best gutter cleaning method and mainly effective for dry leaves. This uses high pressure systems that need a power of about 300 watts and the suction comes from a pipe that is about 50mm in diameter.

Cicero Plumbers

There is non-stop air pressure that sucks in the leaves into a storage tank. Most of the reputed guttering services use this system due to its effectiveness but there are other methods as well.

Our professionals have different types of advanced tools to ensure your gutter is clean and rightly placed.

Gutter cleaning is a chore and would you be able to do it all by yourself even if you have read the DIY tips? Remember that execution is nothing simple. It is always best to hire our professional plumbers in Kansas without doing it on your own using the tallest ladder. Safety comes first and this is why you must rely on us. There are so many people who are injured every year due to this.

Another very important aspect is executing an impressive gutter maintenance plan. It is best to hire our experienced contractors to inspect your property at regular intervals. We ensure the gutters are in place, intact and connected to downspouts. Professional gutter cleaning is not a big investment but the return is worth.

The best thing to do is to get the gutter cleaning twice a year, in the Spring and the Fall. It is a part of regular maintenance and this way you could save yourself from huge drainage costs. Not taking care of those unimpressive gutters could leave you in big mess; so do not ignore and call us today !

 

Posted on: July 12, 2018

How to fix a dripping tap in your Chicago Home

Leaky kitchen faucetA dripping tap means wastage of water and rising water bills without any use (which could be really expensive!)  It could also lead to damage of property raising your insurance claims.

Repairing is the best solution, you may try some DIY  procedures to fix your dripping tap, or,  you can avoid the hassle and contact a professional plumber in Chicago.

There are many plumbing agencies that offer smart service by immediately fixing dripping taps. In case you have some technical skills and wish to try out things on your own at first, you can follow the steps.

At first you need to turn off the water supply and this is really easy when the isolation vales are located in close proximity to the tap. You can even identify whether ceramic washers are fixed to the tap or rubber washers.

If you have a rubber washer tap, you simply need to change the small washer and if it’s a ceramic one, you need to replace the entire valve. Torn O-rings are usually the cause of a leaking tap mainly in the kitchen. So if the tap is still dripping water after replacing the washer, it’s the O-rings that are responsible.

Rubber washers are delicate so you need to protect and take adequate care while turning the tap on and off. Do not over-tighten while turning off the tap to prevent a dripping tap.

Steps to fixing a dripping tap

  1. Turn the water supply – Run the tap and make sure there is no more water in it.
  2. The screw – The screw is important because it hold the entire tap in a place together. Loosen the screws to make necessary repairs. The screw is mainly hidden beneath the stylish cold and hot caps located on the tap top or sometimes beneath the cold and hot indicator. It’s easy to use your hands to unscrew the caps or just use a screwdriver.
  3. Taking tap apart – You need to take off the head of the tap and there could be a piece of metal covering the tap neck safeguarding the valve, just take that off as well.remodeling a kitchen in High Springs
  4. Ceramic disc replacement–The metal shroud covers the valve, use an adjustable spanner to turn it, once it’s loose just remove. Place the new cartridge in and fix the tap.
  5. Changing the rubber washer–Slide the old rubber washer and put on the new one. Put back the valve and the tap back
  6. O-ring replacement–The O-ring is a bigger size washer located at the bottom of the tap spout. The O-ring is located at the base; take a screw-driver to replace the old ring with the new one. Use a pair of scissors to snip it off and tighten the grub screw again.

Its wise of you get repair a dripping tap on time, or else you might have to call an emergency plumber agency in your Chicago home. It’s a real head ache if the tap continues to drip and if you cannot spot the problem, call a plumber.

Posted on: July 5, 2018

Showerhead Cleaning in Your Boston Home

shower head faucetShowerheads are daily used bathroom fittings that give us a luxurious bathing experience; it’s the same kind as a faucet. Due to prolonged use, showerheads tend to get clogged and this is why you need to maintain it yourself. If you don’t clean showers for a long time, it could get jammed, water flow could stop or slow down and you may need to call our expert technicians in Boston .

You might notice that sometimes your showerhead might sprinkle water unevenly. Do you know why such happens? It’s because the holes get clogged with minerals deposits. One very easy home remedy is to open and soak the showerhead in vinegar,

Incase you cannot remove the showerhead; just soak it using a plastic bag or a rubber band. This is best for showerheads made of stainless steel, chrome or other metal surface. Firstly, slip the rubber band right at the top of the showerhead and wind it around the shower arm so that the plastic bag stays fixed. Now fill the plastic with white vinegar. Now, fasten the plastic bag to the showerhead by slipping its top from beneath the rubber band. Keep it for an hour, remove the vinegar filled bag and wash it with water. Wipe with a soft cloth.

Essential Steps to Keeping Your Showerhead Clean

If there is very thick mineral deposition, you need to opt for advanced cleaning. Here are the steps that you can do at home:

  • Disconnect the showerhead and make sure you don’t spoil the finish of the fixture while unscrewing. It is better not to use pliers but a wrench instead.
  • Wash the showerhead using a sharp but narrow gush of water so that the debris is loosened to some extent.
  • Open and clean the showerhead using a scrubber or old toothbrush and vinegar, you can also use a safety pin to loosen the deposits. Wash again and do this a couple of times.
  • Reinstall once it’s clean and make sure the seal is tight.

 Here are some precautions

Make sure you are handling shower and showerhead with care because excessive cleaning using tough agents could damage the surface and the inner parts also could be harmed. Do not make mistakes while cleaning dirt and limescale, any wrong treatment could lead to damage. Do not spray any sort of cleaning agent directly on the showers instead use a soft wet cloth.

Any cleaning compound containing hydrochloric acid, chlorine, formic acid or acetic acid could lead to great damage. Bleach is never a good idea to clean showerheads as it could lead to birth of more bacteria. And, if you do not want to do all the above trial and error methods yourself, it is advisable to call our professional contractors in Boston and seek our expert advice.

Installing new showers and faucetsFort Smith fixing shower

Now you might also wish to change the look and feel of your bathroom by installing new shower and showerhead. There are different types of fixtures like single handed, two handed and also two handed with diverter. Some of the usual showerheads are:

  • Single head and wall mounted
  • Rain shower
  • Hand held

Factors to remember while buying a showerhead

If you are thinking which one to buy, take a look at the decisive factors:

  • All showerheads need different psi (pressure) for flowing effectively. Buy a head that is good for the kind of water pressure you have at home.
  • Each and every showerhead have varying pattern of spray nozzles so you need to finds out what kind of showerhead you need, some of the options are: wide, targeted, pulsating and rinse.
  • The energy bill depends on the water pressure your showerhead would require. Opt for one that comes with WaterSense label.
  • Finally look and feel is also an important factor; it must match with the décor of your bathroom.

Get a makeover now

In just few hours you can get back an amazing bathroom with new showers, faucets and fittings. You won’t have to deal with leaking showers anymore, thus you can save on your water bill. For a quick makeover or repair its best to call our professional plumbers in Boston.

We can install a variety of shower faucets and bathtubs catering to your personal style and taste. Installing a showerhead is not a very expensive project and you must upgrade to a new one in every 5 years.Call us for a quote in Boston !

Posted on: June 29, 2018

Do I Really Need a Powerflush in My Kansas City Home?

boiler installation syracuseFirst it is important to know what a powerflush is because a lot of people do not know what it is.  It is a cleaning process that is carried out on a central heating system with the help of a Powerflush pump. The main task of Powerflush is to remove all debris, dirt, rust and sludge from the water running within the heating system pipes.

The point is that: “do I really need a Powerflush in my home?” The answer is: Yes, it is very necessary to make the system efficient after prolonged use. If you don’t powerflush, your boiler could be damaged by the dirty waters. Powerflush is not only about clearing the debris that has already built up in the system, but there are also certain chemicals used in power flushing which slows down further breakdowns in the future within the radiators and pipes.

When Do I actually need a powerflush?

The answer depends on the level of dirt and rust that has built-up in your system for days. Incase you have a system that is few years in age and you never got a powerflush done anytime; you would definitely need one soon. The best way to decide is to take a sample of water from the system and test it from a heating engineer. If you experience the below mentioned symptoms you need powerflush:

  • Unclean bleed water or cold radiators?
  • Boiler cut outs and noises?
  • Fluctuations in temperature or lukewarm water?
  • Blocked pipes and a cold home?
  • Very slow heating

What could happen if you don’t powerflush?

There could be severe damage that would be extremely expensive to repair. Take a look at mainly what happens if you don’t:

  • The system would lose its performance and you would have to pay high fuel and repair bills
  • The heat exchangers and radiators would be filled with pin holes and that would need repair or replacement. A black oil come out known as the oxide sludge and it can damage anything like floors, carpets etc.
  • There could be mechanical failures like in the pumps, hydraulic systems, valves and heat exchangers.

Advantages of power flush

  • The system is more energy efficient
  • The reliability is enhanced
  • Radiators are hotter
  • Less chances of breakdown
  • The lifespan of your system is increased
  • Least noises
  • The heating of radiators will be quicker
  • More hot water supply

Is powerflush a DIY initiative?

It is not recommended to do the power flush yourself because it’s a risky and complex process; there are a lot of equipment and chemicals used. It is best to get in touch with our Gas Safe registered technicians  in your Kansas City.

Do you take care of your boiler?

If you perform an annual servicing of the boiler thenPlumbers in Summer a power flushing after every 5-6 years is sufficient. A power flush prior to installing a new boiler is highly recommended.

One question rings the mind that why is power flush necessary for a new boiler? It is very essential to maintain the warranty because if a new boiler is installed on an unclean water system, there are chances of the heating system getting damaged.

How much does Power flush cost?

Now if you are keen about knowing how much a power flush would cost, it depends on the size of your heating system and how complex the task would be. The service is a bit on the expensive side but its worth as it could save a huge amount of future expenses. Power flushing takes just a day to be done and for smaller systems it takes only a few hours. Contact our plumbing contractors in your Kansas City that offers power flush service at a competitive pricing.

CONCLUSION

Power flushing improves the efficiency because water flows without any hindrance through the pipes when the system water is cleaned. If you imagine the boiler to be a human hear and the pipes as the arteries, you could understand the functionality.

Posted on: June 26, 2018